VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON |

| 1.CHECK CAN COMMUNICATION SYSTEM |
Check if the CAN communication system DTC is output (Click here for LHD, or Click here for RHD).
| Condition | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU connector is securely connected.
|
| ||||
| OK | |
| 3.CHECK BATTERY |
Check the battery voltage.
|
| ||||
| OK | |
| 4.INSPECT SKID CONTROL ECU (IG1 TERMINAL) |
![]() |
Disconnect the skid control ECU connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A26-46 (IG1) - Body ground | Ignition switch on (IG) | 10 to 14 V |
|
| ||||
| OK | |
| 5.INSPECT SKID CONTROL ECU (GND TERMINAL) |
![]() |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A26-32 (GND1) - Body ground | Always | Below 1 Ω |
| A26-1 (GND2) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.INSPECT PARKING BRAKE SWITCH |
![]() |
Disconnect the parking brake switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - Body ground | Parking brake switch ON (Switch pin free) | Below 1 Ω |
| 1 - Body ground | Parking brake switch OFF (Switch pin pushed in) | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH) |
![]() |
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| IC-14 (PKB) - A18-1 | Always | Below 1 Ω |
| IC-14 (PKB) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| IM-2 (PKB) - E33-1 | Always | Below 1 Ω |
| IM-2 (PKB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
![]() |
Remove the reservoir tank cap and strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Float up (Switch OFF) | 1.9 to 2.1 kΩ |
| 1 - 2 | Float down (Switch ON) | Below 1 Ω |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH) |
![]() |
Disconnect the combination meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F2-6 (B/LE) - A16-1 | Always | Below 1 Ω |
| F2-6 (B/LE) - Body ground | Always | 10 kΩ or higher |
| A16-2 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.INSPECT COMBINATION METER ASSEMBLY |
Perform Active Test of the combination meter (meter CPU) using the intelligent tester (Click here).
|
| ||||
| OK | ||
| ||