Home › ENGINE ยท 2AZ-FE › ENGINE MECHANICAL › TIMING CHAIN

TIMING CHAIN > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A134904
  1. Remove the 2 nuts and cover.



3. REMOVE FRONT WHEEL RH


4. REMOVE ENGINE UNDER COVER LH


5. REMOVE ENGINE UNDER COVER RH


6. REMOVE FRONT FENDER APRON SEAL RH


7. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.



8. REMOVE FRONT EXHAUST PIPE ASSEMBLY

HINT:
Click here.



9. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A134912
  1. Remove the 2 bolts and No. 2 mounting stay RH.



10. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY


    A134909
  1. Remove the bolt and disconnect the ground cable.



    A134910
  1. Remove the 3 bolts and the engine moving control rod with bracket.



11. REMOVE NO. 2 ENGINE MOUNTING BRACKET RH


    A134911
  1. Remove the 3 bolts and No. 2 mounting bracket RH.



12. REMOVE V-RIBBED BELT


    A114351E03
  1. Using SST and 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then remove the V-ribbed belt.

    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply force any more than necessary.



13. REMOVE GENERATOR ASSEMBLY


    A135170
  1. Disconnect the generator connector.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and wire harness clamp bracket.

  1. Remove the wire harness clamps.



    A133567
  1. Remove the 2 bolts and generator assembly.



14. REMOVE VANE PUMP ASSEMBLY


    A059879
  1. Disconnect the oil pressure switch connector.

  1. Loosen the 2 bolts and remove the vane pump from the engine.



15. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 4 bolts and 4 ignition coils.



16. DISCONNECT VENTILATION HOSE


17. DISCONNECT NO. 2 VENTILATION HOSE


18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A112210E01
  1. Remove the 2 bolts and disconnect the 2 engine wires.



    A127550E02
  1. Remove the 8 bolts, 2 nuts, and the cylinder head cover.



19. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    A098345E09
  1. Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.

  1. Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration. If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.



20. REMOVE CRANKSHAFT PULLEY


    A013697E02
  1. Using SST, fix the pulley in place and loosen the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A124860E01
  1. Using SST, remove the pulley bolt and pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-40011   (09957-04010)

    HINT:
    If necessary, remove the pulley and pulley bolt using SST.



21. REMOVE CRANK POSITION SENSOR


    A097797
  1. Disconnect the crankshaft position sensor connector.

  1. Remove the connector clamp and wire harness clamp.

  1. Remove the wire harness clamp bracket from the wire harness.

  1. Remove the bolt, and then remove the crankshaft position sensor.



22. REMOVE OIL PAN SUB-ASSEMBLY


    A114333
  1. Remove the 12 bolts and 2 nuts.



    A000019
  1. Insert the blade of oil pan seal cutter between the crankcase and oil pan. Cut through the sealer and remove the oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the crankcase, chain cover and oil pan.



23. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A098348E01
  1. Remove the 2 nuts, tensioner and gasket.

    NOTICE:
    Do not turn the crankshaft without the chain tensioner.



24. INSTALL ENGINE HANGERS


    A052507E05
  1. Install the No. 1 engine hanger and No. 2 engine hanger with the bolts as shown in the illustration.
    Parts No.:
    No. 1 Engine hanger
    12281-28010
    No. 2 Engine hanger
    12282-28010
    Bolt
    91512-61020

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Attach the sling device to the engine hangers and chain block.



25. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
  1. Lift the engine upward using the chain block.

    NOTICE:
    Do not lift the engine more than necessary.



    A112212
  1. Remove the bolt, nut and V-ribbed belt tensioner.



26. REMOVE ENGINE MOUNTING INSULATOR


    A059880
  1. Attach the engine chain hoist to the engine hangers.

    CAUTION:
    Do not attempt to hang the engine by hooking the chain to any other part.

  1. Remove the bolt and disconnect the engine mounting insulator FR.



    A060825E02
  1. M/T:
    Remove the bolt and disconnect the engine lateral control rod.



    A138332
  1. Remove the 2 bolts and disconnect the steering gear return tube clamps from the frame.



    A059900
  1. Remove the 4 nuts from the engine mounting insulator RH.

  1. Raise the engine and remove the engine mounting insulator RH.



27. REMOVE ENGINE MOUNTING BRACKET RH


    A052481
  1. Remove the 3 bolts and engine mounting bracket.



28. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A128178
  1. Using a E10 "TORX" socket, remove the stud bolt for the drive belt tensioner from the cylinder block.

  1. Remove the 12 bolts and 2 nuts.



    A128179
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

    HINT:
    Tape the screwdriver tip before use.



29. REMOVE TIMING CHAIN CASE OIL SEAL


    A128180
  1. Using a screwdriver and a hammer, tap out the oil seal.

    HINT:
    Tape the screwdriver tip before use.



30. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    A132571
  1. Remove the crankshaft position sensor plate.



31. REMOVE CHAIN TENSIONER SLIPPER


    A125372
  1. Remove the bolt and chain tensioner slipper.



32. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A125371
  1. Remove the 2 bolts and chain vibration damper.



33. REMOVE TIMING CHAIN GUIDE


    A125373
  1. Remove the bolt and timing chain guide.



34. REMOVE CHAIN SUB-ASSEMBLY


    A128185
  1. Remove the chain sub-assembly.



35. REMOVE CRANKSHAFT TIMING SPROCKET


    A125374
  1. Remove the crankshaft timing sprocket.



36. REMOVE NO. 2 CHAIN SUB-ASSEMBLY


    A098351E01
  1. Turn the crankshaft by 90° counterclockwise to align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.



    A098352E01
  1. Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.



    B011415E03
  1. Remove the bolt, chain tensioner plate and spring.



    A063847
  1. Remove the chain tensioner, oil pump driven sprocket and chain.