Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly and the seat position airbag sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.
  2. Seat position airbag sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Front seat inner belt assembly LH
  4. Seat position airbag sensor
  5. Center airbag sensor assembly

WIRING DIAGRAM


C123783E01


INSPECTION PROCEDURE

1.CHECK DTC


    C145343E01
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and the seat position airbag sensor.

  1. Check that the connectors (on the center airbag sensor assembly side and seat position airbag sensor side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)


    C145339E01
  1. Using a service wire, connect terminals 14 (DSP+) and 13 (DSP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    1 - 2
    Always
    Below 1 Ω



NG
Go to step 11
OK


5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)


    C145340E01
  1. Disconnect the service wire from connector B.

  1. Measure the resistance between the terminals of connector E according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    1 - 2
    Always
    1 MΩ or higher



NG
Go to step 12
OK


6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)


    C145340E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    1 - Body ground
    Ignition switch ON
    Below 1 V
    2 - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 13
OK


7.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)


    C145340E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    1 - Body ground
    Always
    1 MΩ or higher
    2 - Body ground
    Always
    1 MΩ or higher



NG
Go to step 14
OK


8.CHECK SEAT POSITION AIRBAG SENSOR


    C145343E01
  1. Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


9.REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


10.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C145343E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

11.CHECK WIRE HARNESS (OPEN)


    C145341E01
  1. for LHD:
    Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

    HINT:
    The service wire has already been inserted into connector B.

  1. for RHD:
    Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    N3-2 (LSP+) - N3-4 (LSP-)
    Always
    Below 1 Ω
    for RHD:
    Tester connection
    Condition
    Specified condition
    O24-2 (RSP+) - O24-4 (RSP-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) 

12.CHECK WIRE HARNESS (SHORT)


    C145342E01
  1. for LHD:
    Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

  1. for RHD:
    Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).

  1. Measure the resistance according to the value(s) in the table below.


Standard resistance:
for LHD:
Tester connection
Condition
Specified condition
N3-2 (LSP+) - N3-4 (LSP-)
Always
1 MΩ or higher
for RHD:
Tester connection
Condition
Specified condition
O24-2 (RSP+) - O24-4 (RSP-)
Always
1 MΩ or higher

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) 

13.CHECK WIRE HARNESS (SHORT TO B+)


    C145342E01
  1. Turn the ignition switch off.

  1. Disconnect the negative(-) terminal cable from the battery, and wait for at least 90 seconds.

  1. for LHD:
    Disconnect the floor wire connector from the front seat inner belt assembly (driver side).

  1. for RHD:
    Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.


Standard voltage:
for LHD:
Tester connection
Condition
Specified condition
N3-2 (LSP+) - Body ground
Ignition switch ON
Below 1 V
N3-4 (LSP-) - Body ground
Ignition switch ON
Below 1 V
for RHD:
Tester connection
Condition
Specified condition
O24-2 (RSP+) - Body ground
Ignition switch ON
Below 1 V
O24-4 (RSP-) - Body ground
Ignition switch ON
Below 1 V

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) 

14.CHECK WIRE HARNESS (SHORT TO GROUND)


    C145342E01
  1. Measure the resistance according to the value(s) in the table below.


Standard resistance:
for LHD:
Tester connection
Condition
Specified condition
N3-2 (LSP+) - Body ground
Always
1 MΩ or higher
N3-4 (LSP-) - Body ground
Always
1 MΩ or higher
for RHD:
Tester connection
Condition
Specified condition
O24-2 (RSP+) - Body ground
Always
1 MΩ or higher
O24-4 (RSP-) - Body ground
Always
1 MΩ or higher

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)