DTC B1653/35 Seat Position Airbag Sensor Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1653/35 |
|
|

| 1.CHECK DTC |
![]() |
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the seat position airbag sensor.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and the seat position airbag sensor.
Check that the connectors (on the center airbag sensor assembly side and seat position airbag sensor side) are not damaged.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN) |
![]() |
Using a service wire, connect terminals 14 (DSP+) and 13 (DSP-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| 1 - 2 | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance between the terminals of connector E according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| 1 - 2 | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| 1 - Body ground | Ignition switch ON | Below 1 V |
| 2 - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| 1 - Body ground | Always | 1 MΩ or higher |
| 2 - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK SEAT POSITION AIRBAG SENSOR |
![]() |
Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 9.REPLACE SEAT POSITION AIRBAG SENSOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the seat position airbag sensor (Click here).
| NEXT | |
| 10.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 11.CHECK WIRE HARNESS (OPEN) |
![]() |
for LHD:
Disconnect the floor wire connector from the front seat inner belt assembly (driver side).
for RHD:
Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N3-2 (LSP+) - N3-4 (LSP-) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| O24-2 (RSP+) - O24-4 (RSP-) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 12.CHECK WIRE HARNESS (SHORT) |
![]() |
for LHD:
Disconnect the floor wire connector from the front seat inner belt assembly (driver side).
for RHD:
Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N3-2 (LSP+) - N3-4 (LSP-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O24-2 (RSP+) - O24-4 (RSP-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 13.CHECK WIRE HARNESS (SHORT TO B+) |
![]() |
Turn the ignition switch off.
Disconnect the negative(-) terminal cable from the battery, and wait for at least 90 seconds.
for LHD:
Disconnect the floor wire connector from the front seat inner belt assembly (driver side).
for RHD:
Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (driver side).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N3-2 (LSP+) - Body ground | Ignition switch ON | Below 1 V |
| N3-4 (LSP-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| O24-2 (RSP+) - Body ground | Ignition switch ON | Below 1 V |
| O24-4 (RSP-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 14.CHECK WIRE HARNESS (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N3-2 (LSP+) - Body ground | Always | 1 MΩ or higher |
| N3-4 (LSP-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O24-2 (RSP+) - Body ground | Always | 1 MΩ or higher |
| O24-4 (RSP-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | ||
| ||