NAVIGATION SYSTEM > Steering Pad Switch Circuit |

| 1.INSPECT NAVIGATION RECEIVER ASSEMBLY |
![]() |
Disconnect the navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F24-7 (SW1) - F24-6 (SWG) | No switch pushed | 95 to 105 kΩ |
| F24-7 (SW1) - F24-6 (SWG) | Seek+ switch: pushed | Below 2.5 Ω |
| F24-7 (SW1) - F24-6 (SWG) | Seek- switch: pushed | 312.5 to 345.4 Ω |
| F24-7 (SW1) - F24-6 (SWG) | Volume+ switch: pushed | 950 to 1050 Ω |
| F24-7 (SW1) - F24-6 (SWG) | Volume- switch: pushed | 2954.5 to 3265.5 Ω |
| F24-8 (SW2) - F24-6 (SWG) | No switch pushed | 95 to 105 kΩ |
| F24-8 (SW2) - F24-6 (SWG) | MODE switch: pushed | Below 2.5 Ω |
| F24-8 (SW2) - F24-6 (SWG) | Voice switch: pushed | 2954.5 to 3265.5 Ω |
| F24-8 (SW2) - F24-6 (SWG) | On hook switch: pushed | 312.5 to 345.4 Ω |
| F24-8 (SW2) - F24-6 (SWG) | Off hook switch: pushed | 950 to 1050 Ω |
| *1 | Front view of wire harness connector (to Navigation Receiver Assembly) |
|
| ||||
| OK | ||
| ||
| 2.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a1-10 (AU1) - a1-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| a1-10 (AU1) - a1-8 (EAU) | Seek+ switch: pushed | Below 2.5 Ω |
| a1-10 (AU1) - a1-8 (EAU) | Seek- switch: pushed | 312.5 to 345.4 Ω |
| a1-10 (AU1) - a1-8 (EAU) | Volume+ switch: pushed | 950 to 1050 Ω |
| a1-10 (AU1) - a1-8 (EAU) | Volume- switch: pushed | 2954.5 to 3265.5 Ω |
| a1-9 (AU2) - a1-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| a1-9 (AU2) - a1-8 (EAU) | MODE switch: pushed | Below 2.5 Ω |
| a1-9 (AU2) - a1-8 (EAU) | Voice switch: pushed | 2954.5 to 3265.5 Ω |
| a1-9 (AU2) - a1-8 (EAU) | On hook switch: pushed | 312.5 to 345.4 Ω |
| a1-9 (AU2) - a1-8 (EAU) | Off hook switch: pushed | 950 to 1050 Ω |
|
| ||||
| OK | |
| 3.INSPECT SPIRAL CABLE |
![]() |
Disconnect the spiral cable connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Spiral cable position | Specified Condition |
| a1-8 (EAU) - E18-4 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| a1-10 (AU1) - E18-6 (AU1) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| a1-9 (AU2) - E18-5 (AU2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
| *1 | Component without harness connected (Spiral Cable) |
| *2 | Steering Pad Switch Side |
| *3 | Vehicle Side |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER) |
![]() |
Disconnect the navigation receiver assembly connector.
![]() |
Disconnect the spiral cable connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E18-6 (AU1) - F24-7 (SW1) | Always | Below 1 Ω |
| E18-4 (EAU) - F24-6 (SWG) | Always | Below 1 Ω |
| E18-5 (AU2) - F24-8 (SW2) | Always | Below 1 Ω |
| E18-6 (AU1) - Body ground | Always | 10 kΩ or higher |
| E18-4 (EAU) - Body ground | Always | 10 kΩ or higher |
| E18-5 (AU2) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Navigation Receiver Assembly) |
| *2 | Front view of wire harness connector (to Spiral Cable) |
|
| ||||
| OK | ||
| ||