Home › BODY ELECTRICAL › NAVIGATION › MULTI-DISPLAY

MULTI-DISPLAY > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)

NOTICE:
After the ignition switch is turned off, the navigation receiver assembly (HDD navigation system) records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)


    B226062
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B137272
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226063
  1. Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.



6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226064
  1. Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.



7. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle)


    B226065
  1. Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.

  1. with Seat Heater System:

    1. Disconnect each connector.



8. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)


    B137274E01
  1. Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.



    B137275
  1. Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.

  1. with Seat Heater System:

    1. Disconnect each connector.



9. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)


    B226097
  1. Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.



10. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)


    B137277
  1. Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.



11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B133997E01
  1. Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the upper console panel sub-assembly.

    HINT:
    Set the shift lever in the D position.



12. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY


    B133998E01
  1. Apply protective tape to the areas shown in the illustration.



    B144610
  1. Using a moulding remover, disengage the 3 clips.



    B144611
  1. Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the instrument panel No. 2 register assembly.



13. REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY


    E129205
  1. Remove the 4 bolts.

  1. Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver with heater control panel assembly.



14. REMOVE RADIO NO. 1 BRACKET


    E129206
  1. Remove the 5 bolts and radio No. 1 bracket.



15. REMOVE RADIO NO. 2 BRACKET


    E129207
  1. Remove the 5 bolts and radio No. 2 bracket.



16. REMOVE NAVIGATION RECEIVER ASSEMBLY


    E129208
  1. Remove the navigation receiver assembly as shown in the illustration.