AUDIO AND VISUAL SYSTEM > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the radio receiver, steering pad switch, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch. | A |
| Illumination comes on for all components except radio receiver. | B |
| No illumination comes on (radio receiver, hazard switch, glove box, etc.). | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE) |
![]() |
Disconnect the spiral cable connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E18-12 (IL+2) - Body ground | Light control switch tail or head | 11 to 14 V |
| *1 | Front view of wire harness connector (to Spiral Cable) |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch connector.
Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.

Check if the illumination for the steering pad switch comes on.
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE |
![]() |
Disconnect the steering pad switch and spiral cable connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| a1-8 (EAU) - E18-4 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| a1-5 (IL+2) - E18-12 (IL+2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
| *1 | Component without harness connected (Spiral Cable) |
| *2 | Steering Pad Switch Side |
| *3 | Vehicle Side |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER) |
![]() |
Disconnect the radio receiver and spiral cable connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F8-6 (SWG) - E18-4 (EAU) | Always | Below 1 Ω |
| F8-6 (SWG) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Radio Receiver) |
| *2 | Front view of wire harness connector (to Spiral Cable) |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER) |
![]() |
Disconnect the radio receiver connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F6-10 (ILL+) - Body ground | Light control switch tail or head | 11 to 14 V |
| *1 | Front view of wire harness connector (to Radio Receiver) |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BODY GROUND) |
![]() |
Disconnect the radio receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F6-7 (GND) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Radio Receiver) |
|
| ||||
| OK | ||
| ||