Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Radio Broadcast cannot be Received or Poor Reception

for Preparation Click here


INSPECTION PROCEDURE

1.CHECK RADIO RECEIVER
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:

      Result
      Proceed to
      Automatic station function stops on a station
      A
      Automatic station search function does not stop
      B



B
Go to step 2
A

REPLACE RADIO RECEIVER (Click here)  

2.CHECK OPTIONAL COMPONENTS
  1. Check for optional components (sunshade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result:

      Result
      Proceed to
      Optional components are installed
      A
      Optional components are not installed
      B

      NOTICE:
      Do not remove any optional components installed by the customer without his or her consent.



B
Go to step 3
A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE) 

3.CHECK RADIO RECEIVER


    E159266E01
    E050367E02
  1. Preparation for check

    1. Remove the antenna plug from the radio receiver.

  1. Check for noise

    1. Turn the ignition switch to ACC with the radio receiver connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the radio receiver antenna jack and check that noise can be heard from the speaker.

      OK:
      Noise can be heard from the speaker.

      Text in Illustration 
      *1
      Component without harness connected
      (Radio Receiver*3)
      *2
      Component without harness connected
      (Radio Receiver*4)
      1. *3: w/ Microphone
      1. *4: w/o Microphone



NG
REPLACE RADIO RECEIVER (Click here)
OK


4.CHECK GLASS ANTENNA


    E111994E01
  1. Check for continuity of the antenna.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of the negative probe and press the foil against the wire with your finger, as shown in the illustration.

    OK:
    There is continuity in the antenna.



NG
REPAIR GLASS ANTENNA (Click here)
OK


5.CONFIRM MODEL

Result:

Result
Proceed to
w/o Microphone
A
w/ Microphone
B



B
Go to step 7
A


6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - ANTENNA AMPLIFIER)


    E188416E01
  1. Disconnect the radio receiver and antenna amplifier connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F6-8 (ANT) - F15-1 (B)
    Always
    Below 1 Ω
    F6-8 (ANT) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver)
    *2
    Front view of wire harness connector
    (to Antenna Amplifier)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT RADIO RECEIVER


    E188694E01
  1. Reconnect the F15 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K-2 (+B) - Body ground
    Ignition switch ACC
    Radio switch on
    11 to 14 V
    F15-1 (B) - Body ground
    Ignition switch ACC
    Radio switch on
    11 to 14 V

    Text in Illustration 
    *1
    Component without harness connected
    (Radio Receiver)*3
    *2
    Front view of wire harness connector
    (to Antenna Amplifier)*4
    1. *3: w/ Microphone
    1. *4: w/o Microphone



NG
REPLACE RADIO RECEIVER (Click here)
OK


8.CHECK ANTENNA CORD
  1. Remove the antenna plug of the radio receiver and antenna.

  1. Measure the resistance between the antenna and radio receiver to check for an open circuit in the antenna cord.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard Resistance:
    10 kΩ or higher



NG
REPLACE ANTENNA CORD (Click here)
OK


9.REPLACE AMPLIFIER ANTENNA
  1. Replace the amplifier antenna and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received.



NG
REPLACE RADIO RECEIVER (Click here)
OK

NORMAL OPERATION