TOYOTA PARKING ASSIST-SENSOR SYSTEM > Reverse Signal Circuit |

| 1.INSPECT FUSE (GAUGE NO. 1) |
Remove the GAUGE NO. 1 fuse from the main body ECU (instrument panel junction block ).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| GAUGE NO. 1 fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK CLEARANCE WARNING ECU (REVERSE SIGNAL INPUT) |
![]() |
Disconnect the O28 connector from the clearance warning ECU.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O28-8 (RL) - Body ground | Ignition switch ON, shift lever in R | 7 V or higher |
|
| ||||
| OK | ||
| ||
| 3.CONFIRM MODEL |
Choose the model to be inspected.
| Model | Proceed to |
| for A/T (U250E) | A |
| for A/T (U660E) | B |
| for M/T | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the O28 connector from the clearance warning ECU.
Disconnect the C1 connector from the park/neutral position switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O28-8 (RL) - C1-1 (RL) | Always | Below 1 Ω |
| O28-8 (RL) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT PARK/NEUTRAL POSITION SWITCH |
Remove the park/neutral position switch (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (RL) - 2 (RB) | Shift lever in R | Below 1 Ω |
| 1 (RL) - 2 (RB) | Shift lever in any position except R | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the O28 connector from the clearance warning ECU.
Disconnect the C1 connector from the park/neutral position switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O28-8 (RL) - C1-2 (RL) | Always | Below 1 Ω |
| O28-8 (RL) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT PARK/NEUTRAL POSITION SWITCH |
Remove the park/neutral position switch (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (RL) - 1 (RB) | Shift lever in R | Below 1 Ω |
| 2 (RL) - 1 (RB) | Shift lever in any position except R | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - BACK-UP LIGHT SWITCH) |
![]() |
Disconnect the O28 connector from the clearance warning ECU.
Disconnect the C28 connector from the back-up light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O28-8 (RL) - C28-1 | Always | Below 1 Ω |
| O28-8 (RL) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT BACK-UP LIGHT SWITCH |
Remove the back-up light switch.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Pushed | Below 1 Ω |
| 1 - 2 | Released | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||