BRAKE ACTUATOR (w/ VSC) > INSTALLATION |
| 1. INSTALL BRAKE ACTUATOR WITH BRAKE ACTUATOR BRACKET ASSEMBLY |
![]() |
Install the brake actuator with brake actuator bracket assembly to the body with the 3 bolts.
![]() |
Temporarily tighten each brake line to the correct positions of the brake actuator with brake actuator bracket assembly as shown in the illustration.
![]() |
Using SST, fully tighten each brake line.
![]() |
Connect the brake actuator connector.
| 2. INSTALL RADIATOR RESERVE TANK ASSEMBLY |
![]() |
Install the radiator reserve tank assembly.
![]() |
Connect the radiator reserve tank hose.
| 3. FILL RESERVOIR WITH BRAKE FLUID |
![]() |
Fill the reservoir with brake fluid.
| 4. BLEED BRAKE LINE |
![]() |
Connect a vinyl tube to the bleeder plug.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (*3).
![]() |
When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*4).
Repeat (*3) and (*4) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for each wheel to bleed the air from the brake line.
| 5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 6. BLEED BRAKE ACTUATOR |
Depress the brake pedal more than 20 times with the ignition switch off.
![]() |
Connect the intelligent tester to the DLC3, then turn the ignition switch on (IG).
Turn the intelligent tester on and select "AIR BLEEDING" on the screen.
Bleed the air according to "Step 1: Increase" on the intelligent tester display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*5).
![]() |
When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*6).
Repeat (*5) and (*6) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for the rest of the wheels to bleed the air from the brake line.
Bleed the air from the suction line according to "Step 2: Inhalation" on the intelligent tester display.
![]() |
Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.
Operate the brake actuator assembly to bleed the air using the intelligent tester (*7).
![]() |
Check that the operation has stopped by referring to the intelligent tester display and tighten the bleeder plug (*8).
Repeat (*7) and (*8) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
For the rest of the wheels, bleed the air in the same way as stated in the above procedure.
Bleed the air from the pressure reduction line according to "Step 3: Decrease" on the intelligent tester display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug (*9).
Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal, and hold it.
![]() |
Tighten the bleeder plug, then release the brake pedal (*10).
Repeat steps (*9) to (*10) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedures for the rest of the brakes to bleed the air from the brake line.
Bleed the air from the brake line again according to "Step 4: Increase" on the intelligent tester display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*11).
![]() |
When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*12).
Repeat (*11) and (*12) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedures for each brake to bleed the air from the brake line.
Finish "AIR BLEEDING" on the intelligent tester and turn off the tester.
Disconnect the intelligent tester from the DLC3.
Turn the ignition switch off.
| 7. INSPECT BRAKE FLUID LEVEL |
Check the fluid level and add fluid if necessary.
| 8. INSPECT FOR BRAKE FLUID LEAKAGE |
| 9. INSPECT SENSOR SIGNAL |
| 10. INSPECT DTC AND CLEAR |
| 11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION |
| 12. INSPECT ACTUATOR WITH INTELLIGENT TESTER |