VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
![]() |
Release the parking brake.
When the ignition switch is turned to the ON position, check that the ABS warning, BRAKE warning, SLIP indicator, and master caution indicator lights come on for approximately 3 seconds.
| Trouble Area | See procedure |
| ABS warning light circuit |
Click here or Click here
|
| BRAKE warning light circuit |
Click here or Click here
|
| VSC warning light circuit |
Click here or Click here
|
| SLIP indicator light circuit |
Click here or Click here
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (INTELLIGENT TESTER) |
![]() |
Procedure to enter Test Mode.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Check that the steering wheel is centered and move the shift lever to the P position (A/T) or apply the parking brake (M/T).
Turn the ignition switch to the ON position.
![]() |
Set the intelligent tester to Test Mode (select "Signal Check").
![]() |
Check that the ABS warning light blinks and "CHECK VSC SYSTEM" is displayed on the multi information display (Test Mode).
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit |
Click here
|
| VSC warning light circuit |
Click here
|
![]() |
Check the ABS sensor.
| ACCELERATION SENSOR CHECK (INTELLIGENT TESTER) |
Keep the vehicle stationary on a level surface for 1 second or more.
| MASTER CYLINDER PRESSURE SENSOR CHECK (INTELLIGENT TESTER) |
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the ABS warning light stays on for 3 seconds.
| SPEED SENSOR CHECK (INTELLIGENT TESTER) |
Check the speed sensor signal.
Drive the vehicle straight ahead.
Accelerate the vehicle to a speed of 28 mph (45 km/h) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
![]() |
Check the VSC sensor.
Check that the "CHECK VSC SYSTEM" is displayed on the multi information display, and perform the check.
| YAW RATE SENSOR CHECK (INTELLIGENT TESTER) |
![]() |
Check the output of the yaw rate sensor.
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
Move the shift lever from P to the D position (A/T) or release the parking brake (M/T) and drive the vehicle at a speed of approximately 3 mph (5 km/h), and turn the steering wheel either to the left or right 90° or more until the vehicle makes a 180° turn.
Stop the vehicle and move the shift lever to the P position (A/T) or apply the parking brake (M/T). Check that the skid control buzzer sounds for 3 seconds.
| END OF SENSOR CHECK (INTELLIGENT TESTER) |
![]() |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is driving.
| READ DTC OF SIGNAL CHECK FUNCTION (INTELLIGENT TESTER) |
Read the DTC(s) by following the tester screen.
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (SST CHECK WIRE) |
Procedure to enter Test Mode.
Turn the ignition switch off.
Check that the steering wheel is centered and move the shift lever to the P position (A/T) or apply the parking brake (M/T).
![]() |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch to the ON position.
![]() |
Check that the ABS warning light blinks and "CHECK VSC SYSTEM" is displayed on the multi information display (Test Mode).
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit |
Click here
|
| VSC warning light circuit |
Click here
|
![]() |
Check the ABS sensor.
| ACCELERATION SENSOR CHECK (SST CHECK WIRE) |
Keep the vehicle stationary on a level surface for 1 second or more.
| MASTER CYLINDER PRESSURE SENSOR CHECK (SST CHECK WIRE) |
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the ABS warning light stays on for 3 seconds.
| SPEED SENSOR CHECK (SST CHECK WIRE) |
Check the speed sensor signal.
Drive the vehicle straight ahead.
Accelerate the vehicle to a speed of 28 mph (45 km/h) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
![]() |
Check the VSC sensor.
Check that the "CHECK VSC SYSTEM" is displayed on the multi information display, and perform the check.
| YAW RATE SENSOR CHECK (SST CHECK WIRE) |
![]() |
Check the output of the yaw rate sensor.
Keep the vehicle stationary on a level surface for 1 second or more.
Move the shift lever from P to the D position (A/T) or release the parking brake (M/T) and drive the vehicle at a vehicle speed of approximately 3 mph (5 km/h) and turn the steering wheel either to the left or right 90° or more and until the vehicle makes a 180° turn.
Stop the vehicle and move the shift lever to the P position (A/T) or apply the parking brake (M/T). Check that the skid control buzzer sounds for 3 seconds.
| END OF SENSOR CHECK (SST CHECK WIRE) |
![]() |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is driving.
| READ DTC OF SIGNAL CHECK FUNCTION (SST CHECK WIRE) |
![]() |
Using SST, connect terminals TC and CG of the DLC3.
Count the number of blinks of the ABS warning light and read "DIAG VSC" on the multi information display.

After performing the check, disconnect the SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.
Turn the ignition switch to the ON position.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION (Procedure "A") |
| Code No. | Diagnosis | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH | Speed sensor rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | Speed sensor rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | Speed sensor rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | Speed sensor rotor |
| C1279/79 | Acceleration sensor output voltage malfunction |
|
| C1281/81 | Master cylinder pressure sensor output malfunction |
|
| Code No. | Diagnosis | Trouble Area |
| C0371/71 | Yaw rate sensor | Yaw rate and acceleration sensor |