CLUTCH MASTER CYLINDER > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. DRAIN BRAKE FLUID |
| 4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY (for LHD) |
![]() |
Disconnect the mass air flow meter connector (*1).
Disconnect the purge VSV connector (*2).
Disconnect the 2 purge VSV vacuum hoses (*3).
Disconnect the purge line hose from the clamp (*4).
![]() |
Disconnect the No. 2 ventilation hose from the air cleaner hose.
![]() |
Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.
![]() |
Remove the 2 bolts and air cleaner cap.
Remove the air cleaner filter element from the air cleaner case.
| 5. REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for LHD) |
![]() |
Disconnect the hose clamp.
Remove the 3 bolts and air cleaner case.
| 6. REMOVE WIND SHIELD WIPER LINK ASSEMBLY |
| 7. REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY |
![]() |
Remove the 4 bolts, 4 nuts and outer cowl top panel sub-assembly.
| 8. REMOVE BRAKE BOOSTER ASSEMBLY (for LHD) |
| 9. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower instrument panel finish panel LH.
| 12. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Disengage the 3 claws and the 2 clips.
Disconnect each connector and remove the instrument panel sub-assembly.
| 13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
| 14. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
Remove the 2 clips.
Disengage the guide and 4 claws and then remove the instrument cluster finish panel.
| 15. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws <E>.
Disconnect each connector and remove the combination meter assembly.
| 16. DISCONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS |
![]() |
Remove the clip and pin, and disconnect the push rod clevis from the clutch pedal.
| 17. DRAIN BRAKE FLUID |
| 18. DISCONNECT CLUTCH RESERVOIR TUBE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the tube from the clutch master cylinder.
| 19. DISCONNECT CLUTCH LINE |
![]() |
Using SST, disconnect the clutch line.
| 20. REMOVE CLUTCH MASTER CYLINDER ASSEMBLY (for LHD) |
![]() |
Remove the 2 nuts and clutch master cylinder.
Remove the gasket from the clutch master cylinder assembly.
| 21. REMOVE CLUTCH MASTER CYLINDER ASSEMBLY (for RHD) |
![]() |
Remove the 2 nuts and clutch master cylinder.
Remove the gasket from the clutch master cylinder assembly.