AIR CONDITIONING UNIT > REMOVAL |
| 1. PRECAUTION |
| 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM |
Start up the engine.
Turn the A/C switch on.
Operate the cooler compressor at an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
| 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 4. DISCONNECT BATTERY NEGATIVE TERMINAL |
| 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut and the front wiper arm and blade assembly LH.
| 6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut and the front wiper arm and blade assembly RH.
| 7. REMOVE FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Disengage the claw and remove the front fender to cowl side seal LH.
| 8. REMOVE FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Disengage the claw and remove the front fender to cowl side seal RH.
| 9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver sub-assembly.
| 10. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Disconnect the connector.
![]() |
Remove the 4 bolts and the windshield wiper motor and link assembly.
| 11. REMOVE COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY |
![]() |
Disengage the clamp.
Remove the 4 nuts, the 4 bolts and the cowl top outer front panel sub-assembly.
| 12. DISCONNECT SUCTION PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt, and slide the hook connector.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction hose sub-assembly.
| 13. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY |
Disconnect the air conditioning tube and accessory.
Remove the O-ring from the air conditioner tube and accessory.
| 14. DISCONNECT HEATER OUTLET WATER HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.
| 15. DISCONNECT HEATER INLET WATER HOSE |
| 16. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Remove the instrument panel safety pad assembly (Click here).
| 17. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct) |
![]() |
Remove the clip and No. 1 console box duct.
| 18. REMOVE FLOOR CARPET BRACKET LH |
![]() |
Release the clamp.
Turn back the floor carpet.
![]() |
Remove the 3 clips.
Remove the floor carpet bracket LH.
| 19. REMOVE FLOOR CARPET BRACKET RH |
![]() |
Release the clamp.
Turn back the floor carpet.
![]() |
Remove the 3 clips.
Remove the floor carpet bracket RH.
| 20. REMOVE REAR NO. 2 AIR DUCT |
![]() |
Release the 2 claws and remove the rear No. 2 air duct.
| 21. REMOVE REAR NO. 1 AIR DUCT |
![]() |
Release the 2 claws and remove the rear No. 1 air duct.
| 22. REMOVE NO. 1 AIR DUCT |
![]() |
Disengage the 2 claws and remove the No. 1 air duct.
| 23. REMOVE STEERING COLUMN ASSEMBLY |
![]() |
Remove the clamp from the steering column hole shield.
![]() |
Remove the bolt and slide the steering intermediate shaft assembly.
![]() |
Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.
Separate the steering intermediate shaft assembly from the power steering link assembly.
Disconnect the connectors and wire harness clamps from the steering column assembly.
![]() |
Remove the bolt, 2 nuts and the steering column assembly.
| 24. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Disconnect the 2 connectors.
Remove the 2 bolts and air conditioning amplifier assembly.
| 25. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Remove the 28 clamps, disconnect the 11 connectors, and then disconnect the wire harness.
Remove the 6 nuts, 7 bolts, and junction block.

Remove the 2 caps and 2 bolts from the engine compartment side.

Remove the 2 bolts and nut.
Using a "TORX" socket wrench (T40), remove the 5 "TORX" bolts.

Using a hexagon wrench 12 mm, remove the 2 collars and instrument panel reinforcement assembly with the air conditioner unit assembly.
Remove the 3 bolts, 2 screws, and instrument panel reinforcement assembly.
