Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › BLOWER UNIT

BLOWER UNIT > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)

NOTICE:
After the ignition switch is turned off, the navigation receiver assembly (HDD navigation system) records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


4. DISCONNECT BATTERY NEGATIVE TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the terminal to prevent the airbag from deploying. (Click here)



5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E128807
  1. Remove the nut and the front wiper arm and blade assembly LH.



6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E128808
  1. Remove the nut and the front wiper arm and blade assembly RH.



7. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


    E128809
  1. Disengage the claw and remove the front fender to cowl side seal LH.



8. REMOVE FRONT FENDER TO COWL SIDE SEAL RH


    E128810
  1. Disengage the claw and remove the front fender to cowl side seal RH.



9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E128811
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver sub-assembly.



10. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E128812
  1. Disconnect the connector.



    E128813
  1. Remove the 4 bolts and the windshield wiper motor and link assembly.



11. REMOVE COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY


    C132714E01
  1. Disengage the clamp.

  1. Remove the 4 nuts, the 4 bolts and the cowl top outer front panel sub-assembly.



12. DISCONNECT SUCTION PIPE SUB-ASSEMBLY


    E128510
  1. Remove the bolt, and slide the hook connector.

  1. Disconnect the suction pipe sub-assembly.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



13. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY
  1. Disconnect the air conditioning tube and accessory.

  1. Remove the O-ring from the air conditioner tube and accessory.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



14. DISCONNECT HEATER OUTLET WATER HOSE


    E128511
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.

    NOTICE:
    1. Do not apply excessive force to the heater outlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



15. DISCONNECT HEATER INLET WATER HOSE

HINT:
Disconnection procedure for the heater inlet water hose is the same as that for the heater outlet water hose.



16. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Remove the instrument panel safety pad assembly (Click here).



17. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    C129716
  1. Remove the clip and No. 1 console box duct.



18. REMOVE FLOOR CARPET BRACKET LH


    E129146E01
  1. Release the clamp.

  1. Turn back the floor carpet.



    E128512
  1. Remove the 3 clips.

  1. Remove the floor carpet bracket LH.



19. REMOVE FLOOR CARPET BRACKET RH


    E129147E01
  1. Release the clamp.

  1. Turn back the floor carpet.



    E128513
  1. Remove the 3 clips.

  1. Remove the floor carpet bracket RH.



20. REMOVE REAR NO. 2 AIR DUCT


    C129721
  1. Release the 2 claws and remove the rear No. 2 air duct.



21. REMOVE REAR NO. 1 AIR DUCT


    C129722
  1. Release the 2 claws and remove the rear No. 1 air duct.



22. REMOVE NO. 1 AIR DUCT


    C132547
  1. Disengage the 2 claws and remove the No. 1 air duct.



23. REMOVE STEERING COLUMN ASSEMBLY


    C133172
  1. Remove the clamp from the steering column hole shield.



    C132548E02
  1. Remove the bolt and slide the steering intermediate shaft assembly.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.



    C132549E01
  1. Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.

  1. Disconnect the connectors and wire harness clamps from the steering column assembly.



    C133173E01
  1. Remove the bolt, 2 nuts and the steering column assembly.



24. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY


    E128518E01
  1. Disconnect the 2 connectors.

  1. Remove the 2 bolts and air conditioning amplifier assembly.



25. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Remove the 28 clamps, disconnect the 11 connectors, and then disconnect the wire harness.



  1. Remove the 6 nuts, 7 bolts, and junction block.


    E128519



  1. Remove the 2 caps and 2 bolts from the engine compartment side.


    E128520

  1. Remove the 2 bolts and nut.



  1. Using a "TORX" socket wrench (T40), remove the 5 "TORX" bolts.


    E128521E02

    HINT:
    The "TORX" bolts on the passenger side can be removed with the collars for adjustment.

  1. Using a hexagon wrench 12 mm, remove the 2 collars and instrument panel reinforcement assembly with the air conditioner unit assembly.



  1. Remove the 3 bolts, 2 screws, and instrument panel reinforcement assembly.


    E128522



26. REMOVE BLOWER ASSEMBLY


    E128524
  1. Disconnect the connector.

  1. Remove the 2 screws and blower assembly.