DTC B1820/55 Short in Front Driver Side - Side Squib Circuit |
DTC B1821/55 Open in Front Driver Side - Side Squib Circuit |
DTC B1822/55 Short to GND in Front Driver Side - Side Squib Circuit |
DTC B1823/55 Short to B+ in Front Driver Side - Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1820/55 |
|
|
| B1821/55 |
|
|
| B1822/55 |
|
|
| B1823/55 |
|
|

| 1.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY (FRONT DRIVER SIDE - SIDE SQUIB) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the front seat side airbag assembly (driver side).
Connect the black wire side of SST (resistance 2.1 Ω) to connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK WIRE HARNESS (FRONT DRIVER SIDE - SIDE SQUIB CIRCUIT) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector C.
Disconnect the connectors from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| NZ1-1 (SFL+) - Body ground | Ignition switch ON | Below 1 V |
| NZ1-2 (SFL-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| OY1-1 (SFR+) - Body ground | Ignition switch ON | Below 1 V |
| OY1-2 (SFR-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
Check for an open in the circuit.
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| NZ1-1 (SFL+) - NZ1-2 (SFL-) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| OY1-1 (SFR+) - OY1-2 (SFR-) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| NZ1-1 (SFL+) - Body ground | Always | 1 MΩ or higher |
| NZ1-2 (SFL-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| OY1-1 (SFR+) - Body ground | Always | 1 MΩ or higher |
| OY1-2 (SFR-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| NZ1-1 (SFL+) - NZ1-2 (SFL-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| OY1-1 (SFR+) - OY1-2 (SFR-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the front seat side airbag assembly (driver side) and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||