DTC B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1655/37 |
|
|

| 1.CHECK DTC |
![]() |
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly (driver side).
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly (driver side).
Check that the connectors (on the center airbag sensor assembly side and front seat inner belt assembly (driver side) side) are not damaged.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK WIRE HARNESS (OPEN) |
![]() |
Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N3-1 (LBE+) - N3-3 (LBE-) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| O24-1 (RBE+) - O24-3 (RBE-) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK WIRE HARNESS (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N3-1 (LBE+) - N3-3 (LBE-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O24-1 (RBE+) - O24-3 (RBE-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK WIRE HARNESS (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N3-1 (LBE+) - Body ground | Ignition switch ON | Below 1 V |
| N3-3 (LBE-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| O24-1 (RBE+) - Body ground | Ignition switch ON | Below 1 V |
| O24-3 (RBE-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK WIRE HARNESS (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N3-1 (LBE+) - Body ground | Always | 1 MΩ or higher |
| N3-3 (LBE-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O24-1 (RBE+) - Body ground | Always | 1 MΩ or higher |
| O24-3 (RBE-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) |
![]() |
Connect the connector to the center airbag sensor assembly and the front seat inner belt assembly (driver side).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 9.REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat inner belt assembly (driver side) (Click here).
| NEXT | |
| 10.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||