Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1830/57    Short in Driver Side Curtain Shield Squib Circuit

DTC    B1831/57    Open in Driver Side Curtain Shield Squib Circuit

DTC    B1832/57    Short to GND in Driver Side Curtain Shield Squib Circuit

DTC    B1833/57    Short to B+ in Driver Side Curtain Shield Squib Circuit

for Preparation Click here


DESCRIPTION

The driver side curtain shield squib circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly (driver side).
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side curtain shield squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1830/57
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the driver side curtain shield squib circuit during primary check.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Curtain shield airbag assembly (Driver side curtain shield squib)
  4. Center airbag sensor assembly
B1831/57
  1. The center airbag sensor assembly receives an open circuit signal in the driver side curtain shield squib circuit for 2 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Curtain shield airbag assembly (Driver side curtain shield squib)
  4. Center airbag sensor assembly
B1832/57
  1. The center airbag sensor assembly receives a short circuit to ground signal in the driver side curtain shield squib circuit for 0.5 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Curtain shield airbag assembly (Driver side curtain shield squib)
  4. Center airbag sensor assembly
B1833/57
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the driver side curtain shield squib circuit for 0.5 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Curtain shield airbag assembly (Driver side curtain shield squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM


H044107E06


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY (DRIVER SIDE CURTAIN SHIELD SQUIB)


    C123742E04
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the curtain shield airbag assembly (driver side).

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the curtain shield airbag assembly (driver side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert straight the SST into the terminals of the connector.

SST
09843-18060  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833, or 57 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832, B1833, and 57 may be output at this time, but they are not related to this check.



OK
REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY (DRIVER SIDE) (Click here)
NG


2.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check that the wire harness connector (on the curtain shield airbag assembly (driver side) side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


3.CHECK WIRE HARNESS (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT)


    C123744E04
  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to the ON position.

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      for LHD:
      Tester connection
      Condition
      Specified condition
      N21-1 (ICL+) - Body ground
      Ignition switch ON
      Below 1 V
      N21-2 (ICL-) - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Tester connection
      Condition
      Specified condition
      O16-1 (ICR+) - Body ground
      Ignition switch ON
      Below 1 V
      O16-2 (ICR-) - Body ground
      Ignition switch ON
      Below 1 V

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C

  1. Check for an open in the circuit.

    1. Turn the ignition switch to the LOCK position.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester connection
      Condition
      Specified condition
      N21-1 (ICL+) - N21-2 (ICL-)
      Always
      Below 1 Ω
      for RHD:
      Tester connection
      Condition
      Specified condition
      O16-1 (ICR+) - O16-2 (ICR-)
      Always
      Below 1 Ω

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester connection
      Condition
      Specified condition
      N21-1 (ICL+) - Body ground
      Always
      1 MΩ or higher
      N21-2 (ICL-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester connection
      Condition
      Specified condition
      O16-1 (ICR+) - Body ground
      Always
      1 MΩ or higher
      O16-2 (ICR-) - Body ground
      Always
      1 MΩ or higher

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester connection
      Condition
      Specified condition
      N21-1 (ICL+) - N21-2 (ICL-)
      Always
      1 MΩ or higher
      for LHD:
      Tester connection
      Condition
      Specified condition
      O16-1 (ICR+) - O16-2 (ICR-)
      Always
      1 MΩ or higher

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C111695E02
  1. Connect the connectors to the curtain shield airbag assembly (driver side) and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833, or 57 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832, B1833, and 57 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)