Home › TRANSMISSION · U660E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    U0100    Lost Communication with ECM / PCM "A"

for Preparation Click here


DESCRIPTION

The engine control unit intercommunicates with the TCM with the Controller Area Network (CAN).
If there is a problem in this intercommunication, the TCM sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
U0100
  1. Following conditions are met for 1.25 seconds (1 trip detection logic):
    1. Ignition switch on
    2. Battery voltage is 10.5 V or more
    3. No intercommunication between the ECM and TCM
TCM

WIRING DIAGRAM


C122805E01


INSPECTION PROCEDURE

HINT:
  1. Refer to inspection procedure for CAN communication system (Click herefor LHD, Click here for RHD).
  2. If the CAN communication malfunctions, the TCM cannot receive the current data from the ECM. In this case, the freeze frame data output from the TCM have not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is effective to find malfunctions.
  3. The malfunction area can be checked using the BUS CHECK function on the intelligent tester (Click herefor LHD, Click here for RHD).

1.CHECK ECU TERMINAL VOLTAGE (+B AND E1 TERMINALS)


    C133210E08
  1. Disconnect the TCM connector.

  1. Turn the ignition switch on.

  1. Measure the voltage of the TCM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    C56-18 (+B) - C56-8 (E1)
    9 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance of the TCM connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    C56-8 (E1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (TCM - ECM)


    C133242E04
  1. Disconnect the C56 TCM connector.

  1. Disconnect the C58*1 or C55*2 ECM connector.
    *1: for RHD
    *2: for LHD

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    C56-6 (CAN+) - C58-2*1 (CAN+)
    Below 1 Ω
    C56-6 (CAN+) - C55-2*2 (CAN+)
    Below 1 Ω
    C56-7 (CAN-) - C58-1*1 (CAN-)
    Below 1 Ω
    C56-7 (CAN-) - C55-1*2 (CAN-)
    Below 1 Ω
    C56-6 (CAN+) or C58-2*1 (CAN+) - Body ground
    1 MΩ or more
    C56-6 (CAN+) or C55-2*2 (CAN+) - Body ground
    1 MΩ or more
    C56-7 (CAN-) or C58-1*1 (CAN-) - Body ground
    1 MΩ or more
    C56-7 (CAN-) or C55-1*2 (CAN-) - Body ground
    1 MΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK IF DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTC.

  1. Replace the TCM.

    HINT:
    Replace the TCM with the TCM of a normally functioning vehicle of the same model.

  1. Start the engine.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0100
    A
    No DTC
    B



B
REPLACE TCM
A

REPLACE ECM