PARKING BRAKE PEDAL > INSTALLATION |
| 1. INSTALL PARKING BRAKE PEDAL ASSEMBLY (for LHD) |
![]() |
Install the parking brake pedal assembly with the bolt and 2 nuts.
Connect the parking brake switch connector.
Install the No. 1 parking brake cable assembly to the body with the bolt, the nut, and a new No. 1 parking brake cable clamp.

![]() |
Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable assembly.
| 2. INSTALL PARKING BRAKE PEDAL ASSEMBLY (for RHD) |
![]() |
Install the parking brake pedal assembly with the bolt and 2 nuts.
Connect the parking brake switch connector.
![]() |
Install the No. 1 parking brake cable assembly to the body with the bolt.
![]() |
Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable sub-assembly.
| 3. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD) |
![]() |
Engage the 3 claws and install the No. 1 air duct sub-assembly.
| 4. CONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY |
Connect the No. 4 parking brake cable assembly to the No. 1 parking brake cable assembly.
![]() |
Using SST and a wrench, hold the lock nut of the No. 1 parking brake cable and tighten the turnbuckle of the No. 4 parking brake cable assembly.
| 5. INSTALL CENTER AIRBAG SENSOR ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Install the center airbag sensor assembly with the 3 bolts.
Check that there is no looseness in the installation parts of the center airbag sensor assembly.
Connect the holder (with connectors).
Check that the water-proof sheet is properly set.
| 6. INSTALL FLOOR SHIFT LEVER ASSEMBLY |
![]() |
Install the floor shift lever assembly with the 4 bolts.
| 7. INSTALL YAW RATE AND ACCELERATION SENSOR (w/ VSC) |
![]() |
Install the yaw rate and acceleration sensor with the 2 bolts.
Connect the yaw rate and acceleration sensor connector.
| 8. INSTALL FLOOR CARPET BRACKET LH |
| 9. INSTALL FLOOR CARPET BRACKET RH |
| 10. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct) |
![]() |
Install the No. 1 console box duct with the clip.
| 11. INSTALL NO. 2 CONSOLE BOX INSERT FRONT |
![]() |
Engage the clip.
Install the No. 2 console box insert front with the 3 screws <F>.
| 12. INSTALL NO. 1 CONSOLE BOX INSERT FRONT |
![]() |
Engage the clip.
Install the No. 1 console box insert front with the 3 screws <F>.
| 13. INSTALL CONSOLE BOX ASSEMBLY |
![]() |
Install the 2 screws <F>.
![]() |
Install the console box assembly with the 2 bolts <G>.
| 14. INSTALL CONSOLE BOX CARPET |
![]() |
Install the console box carpet.
| 15. INSTALL CONSOLE BOX POCKET |
Install the console box pocket.
| 16. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY |
Connect each connector.
![]() |
Engage the 2 claws and 2 clips.
Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.
| 17. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY |
![]() |
Connect the connector and engage the clamp.
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
| 18. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY |
with Seat Heater System:
Connect each connector.
![]() |
Engage the 6 claws and the 3 clips to install the floor shift position indicator housing sub-assembly.
| 19. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.
| 20. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.
| 21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Install the shift lever knob sub-assembly.
| 22. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Engage the 3 claws and 3 clips.
Install the 4 screws <B>.
Install the lower instrument panel sub-assembly with the bolt <A>.
| 23. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
![]() |
Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover.
| 24. INSTALL COMBINATION METER ASSEMBLY (for RHD) |
![]() |
Connect each connector.
Install the combination meter assembly with the 4 screws <E>.
| 25. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 (for RHD) |
![]() |
Engage the guide and the 4 claws.
Install the instrument cluster finish panel with the 2 clips.
| 26. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for RHD) |
![]() |
Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.
| 27. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD) |
Connect each connector.
![]() |
Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.
| 28. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Install the air hose and connect the connector.
Engage the 2 claws and the DLC3.
Engage the claw and the 4 clips.
Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.
| 29. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 30. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
| 31. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 32. INSTALL FRONT DOOR SCUFF PLATE RH |
| 33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 34. INSPECT SENSOR SIGNAL |