YAW RATE AND ACCELERATION SENSOR (w/ VSC) > INSTALLATION |
| 1. INSTALL YAW RATE AND ACCELERATION SENSOR |
![]() |
Install the yaw rate and acceleration sensor with the 2 bolts.
Connect the yaw rate and acceleration sensor connector.
| 2. INSTALL NO. 1 CONSOLE BOX DUCT (for Automatic Air Conditioning System) |
![]() |
Install the No. 1 console box duct with the clip.
| 3. INSTALL NO. 1 CONSOLE BOX INSERT FRONT (for Automatic Air Conditioning System) |
![]() |
Engage the clip.
Install the No. 1 console box insert front with the 3 screws <F>.
| 4. INSTALL NO. 2 CONSOLE BOX INSERT FRONT (for Automatic Air Conditioning System) |
![]() |
Engage the clip.
Install the No. 2 console box insert front with the 3 screws <F>.
| 5. INSTALL CONSOLE BOX ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Install the 2 screws.
![]() |
Install the console box assembly with the 2 bolts.
| 6. INSTALL CONSOLE BOX CARPET (for Automatic Air Conditioning System) |
![]() |
Install the console box carpet.
| 7. INSTALL CONSOLE BOX POCKET (for Automatic Air Conditioning System) |
Install the console box pocket.
| 8. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY (for Automatic Air Conditioning System) |
Connect each connector.
![]() |
Engage the 2 claws and 2 clips.
Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.
| 9. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Engage the 3 claws and 3 clips.
Install the 4 screws <B>.
Install the lower instrument panel sub-assembly with the bolt <A>.
| 10. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover.
| 11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH (for Automatic Air Conditioning System) |
![]() |
Install the air hose and connect the connector.
Engage the 2 claws and the DLC3.
Engage the claw and the 4 clips.
Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.
| 12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (for Automatic Air Conditioning System) |
| 13. INSTALL FRONT DOOR SCUFF PLATE RH (for Automatic Air Conditioning System) |
| 14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for Automatic Air Conditioning System) |
![]() |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 15. INSTALL FRONT DOOR SCUFF PLATE LH (for Automatic Air Conditioning System) |
![]() |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
| 16. INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Connect the connector and engage the clamp.
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
| 17. INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
| 18. INSTALL UPPER CONSOLE PANEL (for Manual Transaxle) |
![]() |
Engage the 2 claws and the 5 clips to install the upper console panel as shown in the illustration.
| 19. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY |
with Seat Heater System:
Connect each connector.
![]() |
Engage the 6 claws and the 3 clips to install the floor shift position indicator housing sub-assembly.
| 20. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.
| 21. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.
| 22. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Install the shift lever knob sub-assembly.
| 23. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Install the shift lever knob sub-assembly.
| 24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 25. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION |
| 26. INSPECT SENSOR SIGNAL |
| 27. INSPECT DTC AND CLEAR |