DTC B1622/81 Lost Communication with Driver Side - Side Airbag Sensor Assembly |
DTC B1623/81 Driver Side - Side Airbag Sensor Assembly Initialization Incomplete |
DTC B1632/81 Lost Communication with Driver Side Rear Airbag Sensor |
DTC B1633/81 Driver Side Rear Airbag Sensor Initialization Incomplete |
DTC B1642/81 Lost Communication with Driver Side Satellite Sensor Bus |
DTC B1643/81 Driver Side Satellite Sensor Bus Initialization Incomplete |
| DTC No. | DTC Detecting Condition | Trouble Area |
| 1622/81 1623/81 1632/81 1633/81 1642/81 1643/81 |
|
|

| 1.CHECK PRESENT DTC |
![]() |
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the present DTCs (Click here).
| Result | Proceed to |
| Present DTC B1623, B1633, B1643, or 81 is output. | A |
| Present DTC B1628, B1638, B1648, or 82 is output. | B |
| Present DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK PAST DTC |
Check the past DTCs (Click here).
| Result | Proceed to |
| A |
| Past DTC B1622 is output. | B |
|
| ||||
| A | |
| 3.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor (driver side).
|
| ||||
| OK | |
| 4.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and side airbag sensor (driver side).
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor (driver side) side) are not damaged.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK WIRE HARNESS (OPEN) |
![]() |
Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - N7-3 (BBL-) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - O7-3 (BBR-) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK WIRE HARNESS (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - N7-3 (BBL-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - O7-3 (BBR-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK WIRE HARNESS (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - Body ground | Ignition switch ON | Below 1 V |
| N7-3 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| O7-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK WIRE HARNESS (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| N7-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| O7-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 9.CHECK SIDE AIRBAG SENSOR (DRIVER SIDE) |
![]() |
Connect the connector to the center airbag sensor assembly.
Interchange the side airbag sensor (passenger side) with side airbag sensor (driver side) and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1623, B1633, B1643, or 81 is output. | A |
| DTC B1628, B1638, B1648, or 82 is output. | B |
| DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 10.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor (passenger side) and side airbag sensor (driver side) to their original positions and connect the connectors to them.
Check that the connector is properly connected to the rear airbag sensor (driver side).
|
| ||||
| OK | |
| 11.CHECK CONNECTOR |
Disconnect the connectors from the side airbag sensor (driver side) and rear airbag sensor (driver side).
Check that the connector (on the rear airbag sensor (driver side) side) is not damaged.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 12.CHECK WIRE HARNESS (OPEN) |
![]() |
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-1 (BCL+) - N7-2 (BCL-) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| O7-1 (BCR+) - O7-2 (BCR-) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 13.CHECK WIRE HARNESS (SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-1 (BCL+) - N7-2 (BCL-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O7-1 (BCR+) - O7-2 (BCR-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 14.CHECK WIRE HARNESS (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| N7-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| O7-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| O7-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 15.CHECK WIRE HARNESS (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| N7-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O7-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| O7-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 16.CHECK REAR AIRBAG SENSOR (DRIVER SIDE) |
![]() |
Connect the connector to the side airbag sensor (driver side).
Interchange the rear airbag sensor (passenger side) with rear airbag sensor (driver side) and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1623, B1633, B1643, or 81 is output. | A |
| DTC B1628, B1638, B1648, or 82 is output. | B |
| DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 17.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the rear airbag sensor (passenger side) and rear airbag sensor (driver side) to their original positions and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 18.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor (driver side).
|
| ||||
| OK | |
| 19.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and side airbag sensor (driver side).
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor (driver side) side) are not damaged.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 20.CHECK WIRE HARNESS (OPEN) |
![]() |
Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - N7-3 (BBL-) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - O7-3 (BBR-) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 21.CHECK WIRE HARNESS (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - N7-3 (BBL-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - O7-3 (BBR-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 22.CHECK WIRE HARNESS (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - Body ground | Ignition switch ON | Below 1 V |
| N7-3 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| O7-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 23.CHECK WIRE HARNESS (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| N7-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| O7-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 24.CHECK SIDE AIRBAG SENSOR (DRIVER SIDE) |
![]() |
Connect the connector to the center airbag sensor assembly.
Interchange the side airbag sensor (passenger side) with side airbag sensor (driver side) and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1623, B1633, B1643, or 81 is output. | A |
| DTC B1628, B1638, B1648, or 82 is output. | B |
| DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 25.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor (passenger side) and side airbag sensor (driver side) to their original positions and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||