DTC B1627/82 Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly |
DTC B1628/82 Front Passenger Side - Side Airbag Sensor Assembly Initialization Incomplete |
DTC B1637/82 Lost Communication with Passenger Side Rear Airbag Sensor |
DTC B1638/82 Passenger Side Rear Airbag Sensor Initialization Incomplete |
DTC B1647/82 Lost Communication with Front Passenger Side Satellite Sensor Bus |
DTC B1648/82 Front Passenger Side Satellite Sensor Bus Initialization Incomplete |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1627/82 B1628/82 B1637/82 B1638/82 B1647/82 B1648/82 |
|
|

| 1.CHECK DTC |
![]() |
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the present DTCs (Click here).
| Result | Proceed to |
| Present DTC B1628, B1638, B1648, or 82 is output. | A |
| Present DTC B1623, B1633 B1643, or 81 is output. | B |
| Present DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK PAST DTC |
Check the past DTCs (Click here).
| Result | Proceed to |
| A |
| Past DTC B1627 is output. | B |
|
| ||||
| A | |
| 3.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor (passenger side).
|
| ||||
| OK | |
| 4.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and side airbag sensor (passenger side).
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor (passenger side) side) are not damaged.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK WIRE HARNESS (OPEN) |
![]() |
Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - O7-3 (BBR-) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - N7-3 (BBL-) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK WIRE HARNESS (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - O7-3 (BBR-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - N7-3 (BBL-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK WIRE HARNESS (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| O7-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - Body ground | Ignition switch ON | Below 1 V |
| N7-3 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK WIRE HARNESS (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| O7-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| N7-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 9.CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE) |
![]() |
Connect the connector to the center airbag sensor assembly.
Interchange the side airbag sensor (driver side) with side airbag sensor (passenger side) and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1628, B1638, B1648, or 82 is output. | A |
| DTC B1623, B1633, B1643, or 81 is output. | B |
| DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output. | C |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor (driver side) and side airbag sensor (passenger side) to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | |
| 10.CHECK CONNECTION OF CONNECTOR |
Check that the connector is properly connected to the rear airbag sensor (passenger side).
|
| ||||
| OK | |
| 11.CHECK CONNECTOR |
Disconnect the connectors from the side airbag sensor (passenger side) and rear airbag sensor (passenger side).
Check that the connector (on the rear airbag sensor (passenger side) side) is not damaged.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 12.CHECK WIRE HARNESS (OPEN) |
![]() |
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-2 (BCR-) - O7-1 (BCR+) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| N7-2 (BCL-) - N7-1 (BCL+) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 13.CHECK WIRE HARNESS (SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-1 (BCR+) - O7-2 (BCR-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| N7-1 (BCL+) - N7-2 (BCL-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 14.CHECK WIRE HARNESS (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| O7-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| N7-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| N7-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 15.CHECK WIRE HARNESS (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| O7-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| N7-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| N7-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 16.CHECK REAR AIRBAG SENSOR (PASSENGER SIDE) |
![]() |
Connect the connectors to the side airbag sensor (passenger side).
Interchange the side airbag sensor (driver side) with rear airbag sensor (passenger side) and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1628, B1638, B1648, or 82 is output. | A |
| DTC B1623, B1633, B1643, or 81 is output. | B |
| DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 17.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the rear airbag sensor (driver side) and rear airbag sensor (passenger side) to their original positions and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 18.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor (passenger side).
|
| ||||
| OK | |
| 19.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and side airbag sensor (passenger side).
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor (passenger side) side) are not damaged.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 20.CHECK WIRE HARNESS (OPEN) |
![]() |
Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - O7-3 (BBR-) | Always | Below 1 Ω |
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - N7-3 (BBL-) | Always | Below 1 Ω |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 21.CHECK WIRE HARNESS (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - O7-3 (BBR-) | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - N7-3 (BBL-) | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 22.CHECK WIRE HARNESS (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| O7-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - Body ground | Ignition switch ON | Below 1 V |
| N7-3 (BBL-) - Body ground | Ignition switch ON | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 23.CHECK WIRE HARNESS (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O7-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| O7-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Tester connection | Condition | Specified condition |
| N7-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| N7-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 24.CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE) |
![]() |
Connect the connector to the center airbag sensor assembly.
Interchange the side airbag sensor (passenger side) with side airbag sensor (driver side) and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
| Result | Proceed to |
| DTC B1628, B1638, B1648, or 82 is output. | A |
| DTC B1623, B1633, B1643, or 81 is output. | B |
| DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 25.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor (passenger side) and side airbag sensor (driver side) to their original positions and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||