Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1627/82    Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly

DTC    B1628/82    Front Passenger Side - Side Airbag Sensor Assembly Initialization Incomplete

DTC    B1637/82    Lost Communication with Passenger Side Rear Airbag Sensor

DTC    B1638/82    Passenger Side Rear Airbag Sensor Initialization Incomplete

DTC    B1647/82    Lost Communication with Front Passenger Side Satellite Sensor Bus

DTC    B1648/82    Front Passenger Side Satellite Sensor Bus Initialization Incomplete

for Preparation Click here


DESCRIPTION

The circuit for the passenger side - side collision sensor (to determine deployment of the front seat side airbag assembly (passenger side) and curtain shield airbag assembly (passenger side)) is composed of the center airbag sensor assembly, side airbag sensor (passenger side), and rear airbag sensor (passenger side).
The side airbag sensor (passenger side) and rear airbag sensor (passenger side) detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1627/82, B1628/82, B1637/82, B1638/82, B1647/82, or B1648/82 is recorded when a malfunction is detected in the circuit for the passenger side - side collision sensor (to determine deployment of the front seat side airbag assembly (passenger side) and curtain shield airbag assembly (passenger side)).

DTC No.
DTC Detecting Condition
Trouble Area
B1627/82
B1628/82
B1637/82
B1638/82
B1647/82
B1648/82
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger side - side collision sensor (to determine deployment of the front seat side airbag assembly (passenger side) and curtain shield airbag assembly (passenger side)) for 2 seconds.
  1. Side airbag sensor (passenger side) malfunction
  1. Rear airbag sensor (passenger side) malfunction
  1. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Side airbag sensor (Passenger side)
  4. Rear airbag sensor (Passenger side)
  5. Center airbag sensor assembly

WIRING DIAGRAM


C123784E02


INSPECTION PROCEDURE

1.CHECK PRESENT DTC


    C123752E03
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Turn the ignition switch to the LOCK position.

    HINT:
    If a communication error occurs, DTCs for both the driver and passenger sides will be stored simultaneously. To identify the malfunctioning area, turn the ignition switch to the LOCK position and then ON position again.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the present DTCs (Click here).

    Result:
    Result
    Proceed to
    Present DTC B1628, B1638, B1648, or 82 is output.
    A
    Present DTC B1623, B1633 B1643, or 81 is output.
    B
    Present DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output.
    C

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch to the LOCK position and then ON position again.
    2. Codes other than present DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK PAST DTC
  1. Check the past DTCs (Click here).

    Result:
    Result
    Proceed to
    1. Past DTC B1637, B1647, or 82 is output.
    1. Past DTC B1627, B1637, B1647, or 82 is not output.
    A
    Past DTC B1627 is output.
    B

    HINT:
    Codes other than past DTC B1627, B1637, B1647, or 82 may be output at this time, but they are not related to this check.



B
Go to step 18
A


3.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor (passenger side).

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and side airbag sensor (passenger side).

  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor (passenger side) side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


5.CHECK WIRE HARNESS (OPEN)


    C114846E08
  1. Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-4 (BBR+) - O7-3 (BBR-)
    Always
    Below 1 Ω
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-4 (BBL+) - N7-3 (BBL-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


6.CHECK WIRE HARNESS (SHORT)


    C114847E09
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-4 (BBR+) - O7-3 (BBR-)
    Always
    1 MΩ or higher
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-4 (BBL+) - N7-3 (BBL-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


7.CHECK WIRE HARNESS (SHORT TO B+)


    C114847E09
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    O7-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    N7-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


8.CHECK WIRE HARNESS (SHORT TO GROUND)


    C114847E09
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    O7-3 (BBR-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    N7-3 (BBL-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


9.CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE)


    C123752E04
  1. Connect the connector to the center airbag sensor assembly.

  1. Interchange the side airbag sensor (driver side) with side airbag sensor (passenger side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1628, B1638, B1648, or 82 is output.
    A
    DTC B1623, B1633, B1643, or 81 is output.
    B
    DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output.
    C

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor (driver side) and side airbag sensor (passenger side) to their original positions and connect the connectors to them.



B
REPLACE SIDE AIRBAG SENSOR (PASSENGER SIDE) (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


10.CHECK CONNECTION OF CONNECTOR
  1. Check that the connector is properly connected to the rear airbag sensor (passenger side).

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTOR PROPERLY
OK


11.CHECK CONNECTOR
  1. Disconnect the connectors from the side airbag sensor (passenger side) and rear airbag sensor (passenger side).

  1. Check that the connector (on the rear airbag sensor (passenger side) side) is not damaged.

    OK:
    The connector is not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


12.CHECK WIRE HARNESS (OPEN)


    C123725E04
  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-2 (BCR-) - O7-1 (BCR+)
    Always
    Below 1 Ω
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-2 (BCL-) - N7-1 (BCL+)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


13.CHECK WIRE HARNESS (SHORT)


    C114843E18
  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-1 (BCR+) - O7-2 (BCR-)
    Always
    1 MΩ or higher
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-1 (BCL+) - N7-2 (BCL-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


14.CHECK WIRE HARNESS (SHORT TO B+)


    C114843E18
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    O7-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    N7-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


15.CHECK WIRE HARNESS (SHORT TO GROUND)


    C114843E18
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    O7-2 (BCR-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    N7-2 (BCL-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


16.CHECK REAR AIRBAG SENSOR (PASSENGER SIDE)


    C123751E04
  1. Connect the connectors to the side airbag sensor (passenger side).

  1. Interchange the side airbag sensor (driver side) with rear airbag sensor (passenger side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1628, B1638, B1648, or 82 is output.
    A
    DTC B1623, B1633, B1643, or 81 is output.
    B
    DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output.
    C

    HINT:
    Codes other than DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE REAR AIRBAG SENSOR (PASSENGER SIDE) (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


17.CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the rear airbag sensor (driver side) and rear airbag sensor (passenger side) to their original positions and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1628, B1638, B1648, or 82 is not output.

    HINT:
    Codes other than DTC B1628, B1638, B1648, or 82 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

18.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor (passenger side).

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


19.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and side airbag sensor (passenger side).

  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor (passenger side) side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


20.CHECK WIRE HARNESS (OPEN)


    C114846E08
  1. Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-4 (BBR+) - O7-3 (BBR-)
    Always
    Below 1 Ω
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-4 (BBL+) - N7-3 (BBL-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


21.CHECK WIRE HARNESS (SHORT)


    C114847E09
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-4 (BBR+) - O7-3 (BBR-)
    Always
    1 MΩ or higher
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-4 (BBL+) - N7-3 (BBL-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


22.CHECK WIRE HARNESS (SHORT TO B+)


    C114847E09
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    O7-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    N7-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


23.CHECK WIRE HARNESS (SHORT TO GROUND)


    C114847E09
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester connection
    Condition
    Specified condition
    O7-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    O7-3 (BBR-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester connection
    Condition
    Specified condition
    N7-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    N7-3 (BBL-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


24.CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE)


    C123752E04
  1. Connect the connector to the center airbag sensor assembly.

  1. Interchange the side airbag sensor (passenger side) with side airbag sensor (driver side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1628, B1638, B1648, or 82 is output.
    A
    DTC B1623, B1633, B1643, or 81 is output.
    B
    DTC B1623, B1633, B1643, or 81 and B1628, B1638, B1648, or 82 are not output.
    C



B
REPLACE SIDE AIRBAG SENSOR (PASSENGER SIDE) (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


25.CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor (passenger side) and side airbag sensor (driver side) to their original positions and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1628, B1638, B1648, or 82 is not output.

    HINT:
    Codes other than DTC B1628, B1638, B1648, or 82 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)