Home › ENGINE · 2GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A212541E01


INSPECTION PROCEDURE

1.CHECK ECM (#10, #20, #30, #40, #50, #60 VOLTAGE)


    A139137E04
  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage between the terminals.

    Standard voltage:
    RHD:
    Tester Connection
    Specified Condition
    #10 (C58-45) - E01 (C58-22)
    11 to 14 V
    #20 (C58-85) - E01 (C58-22)
    11 to 14 V
    #30 (C58-44) - E01 (C58-22)
    11 to 14 V
    #40 (C58-84) - E01 (C58-22)
    11 to 14 V
    #50 (C58-43) - E01 (C58-22)
    11 to 14 V
    #60 (C58-83) - E01 (C58-22)
    11 to 14 V
    LHD:
    Tester Connection
    Specified Condition
    #10 (C55-45) - E01 (C55-22)
    11 to 14 V
    #20 (C55-85) - E01 (C55-22)
    11 to 14 V
    #30 (C55-44) - E01 (C55-22)
    11 to 14 V
    #40 (C55-84) - E01 (C55-22)
    11 to 14 V
    #50 (C55-43) - E01 (C55-22)
    11 to 14 V
    #60 (C55-83) - E01 (C55-22)
    11 to 14 V

  1. Reconnect the ECM connector.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.INSPECT INJECTOR ASSEMBLY
  1. Inspect the injector assembly (Click here).



NG
REPLACE INJECTOR ASSEMBLY (Click here)
OK


3.INSPECT IGNITION RELAY NO. 2


    B016200E27
  1. Remove the IG2 relay from the engine room R/B.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (Apply battery voltage between terminals 1 and 2)

  1. Reinstall the IG2 relay.



NG
REPLACE IGNITION RELAY NO. 2
OK


4.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR)


    A106388E13
  1. Disconnect the injector connector.

  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    RHD:
    Tester Connection
    Specified Condition
    #10 (C58-45) - C7-1
    Below 1 Ω
    #20 (C58-85) - C9-1
    Below 1 Ω
    #30 (C58-44) - C8-1
    Below 1 Ω
    #40 (C58-84) - C10-1
    Below 1 Ω
    #50 (C58-43) - C36-1
    Below 1 Ω
    #60 (C58-83) - C37-1
    Below 1 Ω
    #10 (C58-45) or C7-1 - Body ground
    10 kΩ or higher
    #20 (C58-85) or C9-1 - Body ground
    10 kΩ or higher
    #30 (C58-44) or C8-1 - Body ground
    10 kΩ or higher
    #40 (C58-84) or C10-1 - Body ground
    10 kΩ or higher
    #50 (C58-43) or C36-1 - Body ground
    10 kΩ or higher
    #60 (C58-83) or C37-1 - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    #10 (C55-45) - C7-1
    Below 1 Ω
    #20 (C55-85) - C9-1
    Below 1 Ω
    #30 (C55-44) - C8-1
    Below 1 Ω
    #40 (C55-84) - C10-1
    Below 1 Ω
    #50 (C55-43) - C36-1
    Below 1 Ω
    #60 (C55-83) - C37-1
    Below 1 Ω
    #10 (C55-45) or C7-1 - Body ground
    10 kΩ or higher
    #20 (C55-85) or C9-1 - Body ground
    10 kΩ or higher
    #30 (C55-44) or C8-1 - Body ground
    10 kΩ or higher
    #40 (C55-84) or C10-1 - Body ground
    10 kΩ or higher
    #50 (C55-43) or C36-1 - Body ground
    10 kΩ or higher
    #60 (C55-83) or C37-1 - Body ground
    10 kΩ or higher

  1. Reconnect the injector connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (INJECTOR - IG2 RELAY)


    A143981E01
  1. Remove the IG2 relay from the engine room relay block.

  1. Disconnect the injector connectors.

  1. Measure the resistance between the terminals.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    C7-2 - IG2 relay terminal 3
    Below 1 Ω
    C9-2 - IG2 relay terminal 3
    Below 1 Ω
    C8-2 - IG2 relay terminal 3
    Below 1 Ω
    C10-2 - IG2 relay terminal 3
    Below 1 Ω
    C36-2 - IG2 relay terminal 3
    Below 1 Ω
    C37-2 - IG2 relay terminal 3
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    C7-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C9-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C8-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C10-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C36-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    C37-2 or IG2 relay terminal 3 - Body ground
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT FUSE (IG2 FUSE)


    A143982E01
  1. Remove the IG2 fuse from the engine room relay block.

  1. Measure the IG2 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the IG2 fuse.



NG
REPLACE IG2 FUSE
OK


7.INSPECT IGNITION RELAY NO. 2 (VOLTAGE)


    A137039E05
  1. Remove the IG2 relay from the engine room relay block.

  1. Measure the IG2 relay voltage.

    Standard voltage:
    9 to 14 V

  1. Reinstall the IG2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - BATTERY)
OK


8.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)


    A137039E04
  1. Remove the IG2 relay from the engine room R/B.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    IG2 relay terminal 2 - Body ground
    Below 1 Ω

  1. Reinstall the IG2 relay.

    Result:
    Result
    Proceed to
    OK
    A
    NG
    B



B
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


9.CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU)


    A212547E01
  1. Remove the IG2 relay from the engine room relay block.

  1. Disconnect the E6 main body ECU connector.

  1. Measure the resistance between the terminals.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    IG2 relay terminal 1 - IG2D (E6-11)
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    IG2 relay terminal 1 or IG2D (E6-11) - Body ground
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ENTRY AND START SYSTEM