SFI SYSTEM > Fuel Injector Circuit |

| 1.CHECK ECM (#10, #20, #30, #40, #50, #60 VOLTAGE) |
![]() |
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Turn the engine switch on (IG).
Measure the voltage between the terminals.
| Tester Connection | Specified Condition |
| #10 (C58-45) - E01 (C58-22) | 11 to 14 V |
| #20 (C58-85) - E01 (C58-22) | 11 to 14 V |
| #30 (C58-44) - E01 (C58-22) | 11 to 14 V |
| #40 (C58-84) - E01 (C58-22) | 11 to 14 V |
| #50 (C58-43) - E01 (C58-22) | 11 to 14 V |
| #60 (C58-83) - E01 (C58-22) | 11 to 14 V |
| Tester Connection | Specified Condition |
| #10 (C55-45) - E01 (C55-22) | 11 to 14 V |
| #20 (C55-85) - E01 (C55-22) | 11 to 14 V |
| #30 (C55-44) - E01 (C55-22) | 11 to 14 V |
| #40 (C55-84) - E01 (C55-22) | 11 to 14 V |
| #50 (C55-43) - E01 (C55-22) | 11 to 14 V |
| #60 (C55-83) - E01 (C55-22) | 11 to 14 V |
Reconnect the ECM connector.
|
| ||||
| NG | |
| 2.INSPECT INJECTOR ASSEMBLY |
Inspect the injector assembly (Click here).
|
| ||||
| OK | |
| 3.INSPECT IGNITION RELAY NO. 2 |
![]() |
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (Apply battery voltage between terminals 1 and 2) |
Reinstall the IG2 relay.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR) |
![]() |
Disconnect the injector connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| #10 (C58-45) - C7-1 | Below 1 Ω |
| #20 (C58-85) - C9-1 | Below 1 Ω |
| #30 (C58-44) - C8-1 | Below 1 Ω |
| #40 (C58-84) - C10-1 | Below 1 Ω |
| #50 (C58-43) - C36-1 | Below 1 Ω |
| #60 (C58-83) - C37-1 | Below 1 Ω |
| #10 (C58-45) or C7-1 - Body ground | 10 kΩ or higher |
| #20 (C58-85) or C9-1 - Body ground | 10 kΩ or higher |
| #30 (C58-44) or C8-1 - Body ground | 10 kΩ or higher |
| #40 (C58-84) or C10-1 - Body ground | 10 kΩ or higher |
| #50 (C58-43) or C36-1 - Body ground | 10 kΩ or higher |
| #60 (C58-83) or C37-1 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| #10 (C55-45) - C7-1 | Below 1 Ω |
| #20 (C55-85) - C9-1 | Below 1 Ω |
| #30 (C55-44) - C8-1 | Below 1 Ω |
| #40 (C55-84) - C10-1 | Below 1 Ω |
| #50 (C55-43) - C36-1 | Below 1 Ω |
| #60 (C55-83) - C37-1 | Below 1 Ω |
| #10 (C55-45) or C7-1 - Body ground | 10 kΩ or higher |
| #20 (C55-85) or C9-1 - Body ground | 10 kΩ or higher |
| #30 (C55-44) or C8-1 - Body ground | 10 kΩ or higher |
| #40 (C55-84) or C10-1 - Body ground | 10 kΩ or higher |
| #50 (C55-43) or C36-1 - Body ground | 10 kΩ or higher |
| #60 (C55-83) or C37-1 - Body ground | 10 kΩ or higher |
Reconnect the injector connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (INJECTOR - IG2 RELAY) |
![]() |
Remove the IG2 relay from the engine room relay block.
Disconnect the injector connectors.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| C7-2 - IG2 relay terminal 3 | Below 1 Ω |
| C9-2 - IG2 relay terminal 3 | Below 1 Ω |
| C8-2 - IG2 relay terminal 3 | Below 1 Ω |
| C10-2 - IG2 relay terminal 3 | Below 1 Ω |
| C36-2 - IG2 relay terminal 3 | Below 1 Ω |
| C37-2 - IG2 relay terminal 3 | Below 1 Ω |
| Tester Connection | Specified Condition |
| C7-2 or IG2 relay terminal 3 - Body ground | 10 kΩ or higher |
| C9-2 or IG2 relay terminal 3 - Body ground | 10 kΩ or higher |
| C8-2 or IG2 relay terminal 3 - Body ground | 10 kΩ or higher |
| C10-2 or IG2 relay terminal 3 - Body ground | 10 kΩ or higher |
| C36-2 or IG2 relay terminal 3 - Body ground | 10 kΩ or higher |
| C37-2 or IG2 relay terminal 3 - Body ground | 10 kΩ or higher |
Reinstall the IG2 relay.
Reconnect the injector connectors.
|
| ||||
| OK | |
| 6.INSPECT FUSE (IG2 FUSE) |
![]() |
Remove the IG2 fuse from the engine room relay block.
Measure the IG2 fuse resistance.
Reinstall the IG2 fuse.
|
| ||||
| OK | |
| 7.INSPECT IGNITION RELAY NO. 2 (VOLTAGE) |
![]() |
Remove the IG2 relay from the engine room relay block.
Measure the IG2 relay voltage.
Reinstall the IG2 relay.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND) |
![]() |
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| IG2 relay terminal 2 - Body ground | Below 1 Ω |
Reinstall the IG2 relay.
| Result | Proceed to |
| OK | A |
| NG | B |
|
| ||||
| A | |
| 9.CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU) |
![]() |
Remove the IG2 relay from the engine room relay block.
Disconnect the E6 main body ECU connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| IG2 relay terminal 1 - IG2D (E6-11) | Below 1 Ω |
| Tester Connection | Specified Condition |
| IG2 relay terminal 1 or IG2D (E6-11) - Body ground | 10 kΩ or higher |
Reinstall the IG2 relay.
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||