Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE UNIT › 2011.10–2013.07
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073932 ENGINE UNIT G

2AR-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A160725

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the valve rocker arm sub-assembly.


Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the adjuster free from dirt and foreign matter.

·

Use only clean engine oil.



A293105
1.5,0.302 1.969,0.302 false 2.344,0.302 2.875,0.302 false 1.448,0.958 2.052,0.698 true 2.313,0.698 2.896,0.865 true 1.5,1.125 2.063,0.938 false 2.302,0.938 2.833,1.083 false 1.385,1.406 2.052,1.229 true 2.313,1.219 2.938,1.365 true 1.302,1.99 2.052,1.583 true 2.323,1.573 3.042,1.969 true 1.469,2.115 2.063,1.958 true 2.323,1.958 2.875,2.104 true 4.698,1.104 5.052,1.354 false 2.115,0.844 2.427,1 0.313,0.156 10 *1 2.115,1.469 2.427,1.625 0.313,0.156 10 *2 1.229,0.031 1.542,0.188 0.313,0.156 10 *a 3.01,0.031 3.323,0.188 0.313,0.156 10 *b 2.115,0.594 2.427,0.75 0.313,0.156 10 *c 2.115,1.135 2.427,1.292 0.313,0.156 10 *d 2.115,1.854 2.427,2.01 0.313,0.156 10 *e 2.031,0.219 2.49,0.417 0.458,0.198 10 SST 4.427,0.938 4.885,1.135 0.458,0.198 10 SST
*1 Plunger *2 Check Ball
*a CORRECT *b INCORRECT
*c Taper Part *d Low Pressure Chamber
*e High Pressure Chamber - -


a.

Place the lash adjuster into a container full of new engine oil.


b.

Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 4.INSPECT CAMSHAFT THRUST CLEARANCE

Hide 13511 5.INSPECT CAMSHAFT

a.
A196939

Inspect the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.

HINT:

Check the oil clearance after replacing the camshaft.




b.
A196940

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
Intake 44.163 to 44.305 mm (1.739 to 1.744 in.)
Exhaust 44.144 to 44.286 mm (1.738 to 1.744 in.)


Minimum Cam Lobe Height:
Item Specified Condition
Intake 44.013 mm (1.733 in.)
Exhaust 43.996 mm (1.732 in.)


If the cam lobe height is less than the minimum, replace the camshaft sub-assembly.



c.
A196941

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.356 to 1.357 in.)
Other journals 22.959 to 22.975 mm (0.904 to 0.905 in.)


If the journal diameter is not as specified, check the oil clearance.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>CYLINDER HEAD>INSPECTION



Hide 13050 6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A196901C36
1.979,0.625 1.854,0.625 1.854,0.625 1.635,0.906 false 1.25,0.208 1.125,0.208 1.125,0.208 0.698,0.771 false 1.292,0.115 1.5,0.323 0.208,0.208 10 false *1 2.021,0.542 2.281,0.729 0.26,0.188 10 false *2
*1 Pin Hole
*2 Knock Pin


Align and attach the knock pin of the camshaft with the pin hole of the camshaft timing gear.


b.
A196904C56
2.167,0.854 1.917,0.854 1.917,0.854 1.5,1.083 false 0.823,0.75 0.917,0.75 0.917,0.75 1.146,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Gear Assembly
*2 Flange
*a INCORRECT
*b CORRECT
*c Clearance
*d No Clearance


Check that there is no clearance between the camshaft timing gear and camshaft flange.


c.

Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing gear by hand.

NOTICE:

Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



d.

Check the lock of the camshaft timing gear.

i.

Make sure that the camshaft timing gear is locked.

NOTICE:

Be careful not to damage the camshaft.




e.

Release the lock pin.

A284097
1.417,1.052 1.771,1.052 1.771,1.052 1.917,1.104 false 2.344,1.229 2.479,1.125 2.479,1.125 2.781,1.125 false 2.542,2.552 2.677,2.448 2.677,2.448 2.906,2.448 false 2.115,2.792 2.281,2.958 2.281,2.958 2.906,2.958 false 1.344,2.552 1.635,2.552 1.635,2.552 1.771,2.427 false 4.813,1.156 5.073,1.156 5.073,1.156 5.323,1.604 false 4.615,1.51 4.76,1.51 4.76,1.51 5.094,1.76 false 4.615,2.521 4.813,2.521 4.813,2.521 5.125,2.135 false 5.604,1.771 5.948,1.448 5.948,1.448 6.146,1.448 false 5.552,2.167 5.885,2.469 5.885,2.469 6.094,2.469 false 2.958,2.354 3.271,2.51 0.313,0.156 10 false *1 2.958,2.865 3.271,3.021 0.313,0.156 10 false *2 4.615,1.073 4.927,1.229 0.313,0.156 10 false *3 1.229,0.948 1.542,1.104 0.313,0.156 10 false *a 2.844,1.031 3.156,1.188 0.313,0.156 10 false *b 4.438,1.406 4.75,1.563 0.313,0.156 10 false *c 4.448,2.417 4.76,2.573 0.313,0.156 10 false *d 6.135,2.365 6.448,2.521 0.313,0.156 10 false *d 6.188,1.344 6.5,1.5 0.313,0.156 10 false *d 1.198,2.469 1.51,2.625 0.313,0.156 10 false A
*1 Rubber *2 Vinyl Tape
*3 Knock Pin - -
*a Retard Side Path *b Advance Side Path
*c Open *d Close


i.

Clean the camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the camshaft. Plug three of the paths with pieces of rubber.



iii.

Open a hole at port A shown in the illustration.


iv.
A196906

While applying approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the oil path, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.


NOTICE:

Do not allow the camshaft timing gear assembly to lock. If it locks, release the lock pin again.


HINT:
·

The camshaft timing gear assembly may be turned in the advance direction without applying any force.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.





f.

Check for smooth rotation.

i.

Turn the camshaft timing gear within its movable range (26.5 to 28.5°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

NOTICE:

Do not allow the camshaft timing gear assembly to lock.

If it locks, release the lock pin again.




g.

Remove the vinyl tape and rubber pieces from the camshaft.


h.

Remove the bolt and camshaft timing gear.


Hide 13070A 7.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A196902C21
1.896,0.656 1.771,0.656 1.771,0.656 1.594,0.927 false 1.229,0.177 1.104,0.177 1.104,0.177 0.667,0.802 false 2,0.573 2.167,0.74 0.167,0.167 10 false *2 1.281,0.115 1.594,0.313 0.313,0.198 10 false *1
*1 Pin Hole
*2 Knock Pin


Align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear.


b.
A196904C56
2.167,0.854 1.917,0.854 1.917,0.854 1.5,1.083 false 0.823,0.75 0.917,0.75 0.917,0.75 1.146,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Exhaust Gear Assembly
*2 Flange
*a INCORRECT
*b CORRECT
*c Clearance
*d No Clearance


Check that there is no clearance between the camshaft timing exhaust gear and camshaft flange.


c.

Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing exhaust gear by hand.


d.

Check the lock of the camshaft timing exhaust gear.

i.

Make sure that the camshaft timing exhaust gear is locked.

NOTICE:

Be careful not to damage the camshaft.




e.

Release the lock pin.

A292249
1.25,1.115 1.677,1.115 false 2.094,1.219 2.521,1.219 false 1.031,2.823 1.448,2.698 false 2.323,2.375 2.781,2.5 true 5.042,1.208 5.354,1.573 false 4.625,1.542 5.135,1.74 false 4.688,2.406 5.167,2.104 false 5.604,2.125 6.063,2.417 false 5.656,1.74 6.135,1.5 false 2.844,2.49 3.156,2.646 0.313,0.156 10 false *1 0.865,2.792 1.177,2.948 0.313,0.156 10 false *2 4.917,1.052 5.229,1.208 0.313,0.156 10 false *3 2.583,1.135 2.896,1.292 0.313,0.156 10 false *a 1.063,1.031 1.375,1.188 0.313,0.156 10 false *b 6.167,1.396 6.479,1.552 0.313,0.156 10 false *c 6.125,2.375 6.438,2.531 0.313,0.156 10 false *d 4.448,1.427 4.76,1.583 0.313,0.156 10 false *c 4.521,2.375 4.833,2.531 0.313,0.156 10 false *d
*1 Rubber *2 Vinyl Tape
*3 Knock Pin - -
*a Retard Side Path *b Advance Side Path
*c Open *d Close


i.

Clean the camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the camshaft. Plug 2 paths with rubber pieces.



iii.

Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.


iv.
A198157
1,0.115 1.146,0.115 1.146,0.115 1.531,1.292 true 2.313,0.052 2.167,0.052 2.167,0.052 1.865,1.135 true 0.792,0.031 0.99,0.198 0.198,0.167 10 false *a 2.344,0.01 2.542,0.177 0.198,0.167 10 false *b
*a Retard Side Path
*b Advance Side Path


Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the two open paths (the advance side path and retard side path).

NOTICE:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.



v.
A198158
1,0.177 1.156,0.177 1.156,0.177 1.521,1.323 false 2.313,0.104 2.24,0.104 2.24,0.104 1.865,1.177 false 0.781,0.073 0.958,0.24 0.177,0.167 10 false *a 2.354,0.01 3.25,0.354 0.896,0.344 10 false *b 1.031,1.635 1.24,1.833 0.208,0.198 10 false *c 2.333,1.51 2.531,1.708 0.198,0.198 10 false *d
*a Retard Side Path
*b Advance Side Path
*c Hold Pressure
*d Decompress


Check that the camshaft timing exhaust gear turns in the retard direction when reducing the air pressure applied to the advance side path.

HINT:

The lock pin is released and the camshaft timing exhaust gear turns in the retard direction.



vi.

When the camshaft timing exhaust gear moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear may abruptly shift in the advance direction and break the lock pin or other parts.




f.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear within its movable range (21.5 to 23.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.

NOTICE:

When the air pressure is released from the advance side path and then from the retard side path, the gear automatically returns to the most advanced position due to the advance assist spring operation, and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




g.

Check the lock at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear locks at the most advanced position.



h.

Remove the vinyl tape and rubber pieces from the camshaft.


i.

Remove the bolt and camshaft timing gear.


Hide 13506 8.INSPECT CHAIN SUB-ASSEMBLY

A168044
2.688,0.073 3.188,0.292 0.5,0.219 10 false 147 N 1.76,1.125 2.052,1.333 0.292,0.208 10 false *a 0.646,1.802 0.781,1.979 0.135,0.177 10 false 0 0.823,1.802 0.938,1.948 0.115,0.146 10 false 1 1,1.802 1.125,1.969 0.125,0.167 10 false 2 1.188,1.802 1.302,1.958 0.115,0.156 10 false 3 1.365,1.802 1.49,1.948 0.125,0.146 10 false 4 1.552,1.802 1.667,1.948 0.115,0.146 10 false 5 2.938,1.792 3.188,2.01 0.25,0.219 10 false 15
*a Measurement Area


a.

Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 pins.

Maximum chain elongation:

137.7 mm (5.42 in.)


HINT:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the chain sub-assembly.


Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A198159

Place the chain around the sprocket.


b.

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

59.94 mm (2.36 in.)


If the diameter is less than the minimum, replace the chain and crankshaft timing sprocket.

HINT:

The vernier caliper must contact the chain rollers for the measurement.



Hide 13540 10.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A198160

Move the stopper plate counterclockwise to release the lock. Push the plunger and check that it moves smoothly.

If necessary, replace the No. 1 chain tensioner assembly.


Hide 13559 11.INSPECT CHAIN TENSIONER SLIPPER

a.
A198161
2.854,0.917 3.125,1.125 0.271,0.208 10 false *a
*a Depth


Measure the worn depth of the chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the chain tensioner slipper.


Hide 13561 12.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A198162
2.792,0.865 3.021,1.083 0.229,0.219 10 false *a
*a Depth


Measure the worn depth of the chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13566B 13.INSPECT TIMING CHAIN GUIDE

a.
A196926
3.021,1.76 3.302,1.99 0.281,0.229 10 false *a
*a Depth


Measure the worn depth of the timing chain guide.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the timing chain guide.


Hide 13620B 14.INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE

a.
A196922

Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.

Standard thrust clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum thrust clearance:

0.09 mm (0.00354 in.)


If the thrust clearance is more than the maximum, replace the engine balancer assembly.


Hide 13620B 15.INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE

a.
A198185

Using a dial indicator, measure the thrust clearance while moving the No. 2 balance shaft back and forth.

Standard thrust clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum thrust clearance:

0.09 mm (0.00354 in.)


If the thrust clearance is more than the maximum, replace the engine balancer assembly.


Hide 13620B 16.INSPECT BALANCE SHAFT BACKLASH

a.
A198163
1.323,0.302 1.563,0.5 0.24,0.198 10 false *a
*a Fix


Secure the No. 2 balance shaft in place, and then using a dial indicator, measure the backlash of the No. 1 and No. 2 balance shafts as shown in the illustration.

Standard backlash:

0.04 to 0.17 mm (0.00157 to 0.00669 in.)


Maximum backlash:

0.17 mm (0.00669 in.)


NOTICE:

Measure at 3 or more areas around the circumference of the No. 1 and No. 2 balance shafts.


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 11101A 17.INSPECT CYLINDER HEAD BOLT

a.
A284095
2.271,0.344 2.583,0.5 0.313,0.156 10 *a 1.24,1.604 2.156,1.802 0.917,0.198 10 106 mm
*a Measurement Point


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard diameter:

10.85 to 11.00 mm (0.427 to 0.433 in.)


Minimum diameter:

10.6 mm (0.417 in.)


Measurement point (distance from the seat):

106 mm (4.17 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head bolt. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head bolt with a new one.




Hide 25051 18.INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.
A196896

Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head.

Maximum warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold converter sub-assembly.