11101
1.INSPECT CYLINDER HEAD SUB-ASSEMBLY
Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head contacts the cylinder block and manifold.
| *a | Cylinder Head Lower Side | *b | Intake Manifold Side |
| *c | Exhaust Manifold Side | - | - |
| Item | Specified Condition |
|---|---|
| Cylinder head lower side | 0.05 mm (0.00197 in.) |
| Intake manifold side | 0.10 mm (0.00394 in.) |
| Exhaust manifold side | 0.10 mm (0.00394 in.) |
If the warpage is more than the maximum, replace the cylinder head.
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head.
13711B
2.INSPECT COMPRESSION SPRING
Type A and Type B can be distinguished by the shape of the compression spring.
| *A | Type A
(Compression Spring Shape: Straight) |
*B | Type B
(Compression Spring Shape: Tapered) |
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Spring Retainer |
| *3 | Compression Spring | *4 | Valve Lash Adjuster Assembly |
Type A:
Using a vernier caliper, measure the free length of the compression spring.
| Wire Diameter | Specified Condition |
|---|---|
| 3.3 mm (0.130 in.) | 49.0 to 51.0 mm (1.93 to 2.01 in.) |
| 3.4 mm (0.134 in.) | 47.2 to 49.2 mm (1.86 to 1.94 in.) |
If the free length is not as specified, replace the compression spring.
| *a | Deviation |
Using a steel square, measure the deviation of the compression spring.
1.0 mm (0.0394 in.)
2°
If the deviation is more than the maximum, replace the compression spring.
Type B:
Using a vernier caliper, measure the free length of the compression spring.
47.38 mm (1.87 in.)
If the free length is not as specified, replace the compression spring.
| *a | Deviation |
| *b | 30 mm (1.18 in.) |
Using a steel square, measure the deviation of the compression spring at the position shown in the illustration.
1.0 mm (0.0394 in.)
If the deviation is more than the maximum, replace the compression spring.
13711
3.INSPECT INTAKE VALVE
Using a micrometer, measure the diameter of the valve stem.
5.470 mm to 5.485 mm (0.21535 to 0.21594 in.)
| *a | Margin Thickness |
Using a vernier caliper, measure the valve head margin thickness.
1.0 mm (0.0394 in.)
0.50 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the valve.
| *a | Overall Length |
Using a vernier caliper, measure the overall length of the valve.
103.92 mm (4.09 in.)
103.42 mm (4.07 in.)
If the overall length is less than the minimum, replace the intake valve.
13715
4.INSPECT EXHAUST VALVE
Using a micrometer, measure the diameter of the valve stem.
5.465 mm to 5.480 mm (0.21516 to 0.21575 in.)
| *a | Margin Thickness |
Using a vernier caliper, measure the valve head margin thickness.
1.0 mm (0.0394 in.)
0.50 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the exhaust valve.
| *a | Overall Length |
Using a vernier caliper, measure the overall length of the valve.
112.91 mm (4.44 in.)
112.41 mm (4.43 in.)
If the overall length is less than the minimum, replace the exhaust valve.
11122
5.INSPECT VALVE GUIDE BUSH OIL CLEARANCE
Using a caliper gauge, measure the inside diameter of the guide bush.
5.510 to 5.530 mm (0.2169 to 0.2177 in.)
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| Item | Specified Condition |
|---|---|
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Specified Condition |
|---|---|
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.10 mm (0.00394 in.) |
If the oil clearance is more than the maximum, replace the valve and guide bush.
11131
6.INSPECT INTAKE VALVE SEAT
Apply a light coat of Prussian blue to the valve face.
| *a | Width |
Lightly press the valve face against the valve seat.
Do not rotate the valve while pressing the valve.
Check the valve face and valve seat.
Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
If not, correct the valve seat.
Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If not, correct the valve seat.
11135
7.INSPECT EXHAUST VALVE SEAT
Apply a light coat of Prussian blue to the valve face.
| *a | Width |
Lightly press the valve face against the valve seat.
Do not rotate the valve while pressing the valve.
Check the valve face and valve seat.
Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
If not, correct the valve seat.
Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If not, correct the valve seat.
13511
8.INSPECT CAMSHAFT OIL CLEARANCE
Do not turn the camshafts.
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
| *1 | Plastigage |
Lay a strip of Plastigage across each of the camshaft journals.
Install the camshaft bearing caps.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>CYLINDER HEAD GASKET>INSTALLATION
Install the camshaft housing sub-assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>CYLINDER HEAD GASKET>REMOVAL
Remove the camshaft bearing caps.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>CYLINDER HEAD GASKET>REMOVAL
| *1 | Plastigage |
| *2 | No. 1 Journal |
| *3 | Other Journal |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
|---|---|
| Intake No. 1 journal | 0.035 to 0.072 mm (0.00137 to 0.00283 in.) |
| Exhaust No. 1 journal | 0.049 to 0.086 mm (0.00193 to 0.00339 in.) |
| Other journal | 0.025 to 0.062 mm (0.000984 to 0.00244 in.) |
| Item | Specified Condition |
|---|---|
| Intake No. 1 journal | 0.085 mm (0.00335 in.) |
| Exhaust No. 1 journal | 0.095 mm (0.00374 in.) |
| Other journal | 0.085 mm (0.00335 in.) |
If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing.
13511
9.INSPECT CAMSHAFT THRUST CLEARANCE
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
Install the camshaft bearing caps.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>CYLINDER HEAD GASKET>INSTALLATION
Install the camshaft housing sub-assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>CYLINDER HEAD GASKET>INSTALLATION
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| Item | Specified Condition |
|---|---|
| Intake | 0.060 to 0.155 mm (0.00236 to 0.00610 in.) |
| Exhaust | 0.060 to 0.155 mm (0.00236 to 0.00610 in.) |
| Item | Specified Condition |
|---|---|
| Intake | 0.170 mm (0.00669 in.) |
| Exhaust | 0.170 mm (0.00669 in.) |
If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.