Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073928 CYLINDER HEAD GASKET A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 11302 1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 17167 4.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25051 5.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 22030 6.REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 17650 7.REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 23814B 8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 12262 9.DISCONNECT NO. 2 VENTILATION HOSE

Hide 11.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.

A292247C13
5.969,2.917 6.219,2.771 false 3.51,5.708 4.646,5.438 false 1.021,2.833 1.031,3.021 false 0.958,0.354 1.271,0.51 0.313,0.156 10 *a 6.25,0.448 6.563,0.604 0.313,0.156 10 *b 5.792,2.875 6.104,3.031 0.313,0.156 10 *c 4.708,5.323 5.021,5.479 0.313,0.156 10 *d 0.969,3.042 1.281,3.198 0.313,0.156 10 *c 6.688,3.656 6.844,3.854 0.156,0.198 10 A 1.646,2.719 1.802,2.917 0.156,0.198 10 A
*a Approximately 7° *b Approximately 32°
*c Timing Mark *d Key


HINT:

"A" is not a timing mark.



b.

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



c.

Remove the crankshaft pulley bolt.


Hide 13566B 12.REMOVE TIMING CHAIN GUIDE

a.
A196878

Remove the bolt and timing chain guide.


Hide 13540 13.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A196879C11
2.458,0.563 2.344,0.563 2.344,0.563 2.25,1.052 false 1.281,0.479 1.406,0.479 1.406,0.479 1.938,1.052 false 2.49,0.5 2.667,0.656 0.177,0.156 10 true *2 1.073,0.396 1.24,0.552 0.167,0.156 10 true *1
*1 Stopper Plate
*2 Plunger


Allow the plunger to extend slightly, and then rotate the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the tensioner.


b.
A196880C10
1.688,1.948 1.406,1.708 1.406,1.708 1.25,1.708 true 1.052,1.646 1.302,1.823 0.25,0.177 10 false *1
*1 Pin


Move the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.


c.
A196877

Remove the 2 bolts, chain tensioner and gasket.


Hide 13559 14.REMOVE CHAIN TENSIONER SLIPPER

a.
A196876

Remove the bolt and chain tensioner slipper.


Hide 13561 16.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A196868

Remove the 2 bolts and chain vibration damper.


Hide 13050 17.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A196882

Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing gear.

NOTICE:
·

Be careful not to damage the cylinder head or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear.




Hide 13070A 18.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A198183

Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing exhaust gear.

NOTICE:
·

Be careful not to damage the cylinder head or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear.




Hide 11103 19.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A196884N08
2.552,0.115 2.656,0.26 0.104,0.146 10 false 9 2.365,1.896 2.458,2.052 0.094,0.156 10 true 1 0.854,1.885 0.948,2.063 0.094,0.177 10 false 2 3.208,0.625 3.323,0.771 0.115,0.146 10 false 3 3.198,1.677 3.292,1.833 0.094,0.156 10 false 4 3.229,1.042 3.344,1.188 0.115,0.146 10 false 5 0.833,0.125 0.948,0.281 0.115,0.156 10 false 6 0.344,1.938 0.469,2.094 0.125,0.156 10 false 7 0.26,0.646 0.354,0.792 0.094,0.146 10 false 8 2.573,1.854 2.75,2 0.177,0.146 10 true 10 1.885,0.604 2.063,0.75 0.177,0.146 10 true 20 1.521,1.865 1.698,2.01 0.177,0.146 10 true 19 1.521,0.094 1.698,0.24 0.177,0.146 10 false 18 2.354,0.635 2.531,0.781 0.177,0.146 10 true 17 2.052,1.865 2.229,2.01 0.177,0.146 10 true 16 2.01,0.104 2.188,0.25 0.177,0.146 10 false 15 1.344,0.625 1.521,0.771 0.177,0.146 10 true 14 1.01,1.854 1.188,2 0.177,0.146 10 true 13 1.073,0.115 1.25,0.26 0.177,0.146 10 false 12 2.99,0.854 3.167,1 0.177,0.146 10 false 11

Uniformly loosen and remove the 20 bearing cap bolts in the sequence shown in the illustration.


b.
A196899

Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.



Hide 20.REMOVE CAMSHAFT BEARING CAP

a.
A196885N11
2.146,1.625 2.25,1.771 0.104,0.146 10 true 9 0.313,1.917 0.406,2.073 0.094,0.156 10 true 1 0.125,0.094 0.219,0.271 0.094,0.177 10 false 2 0.083,0.74 0.198,0.885 0.115,0.146 10 false 3 2.729,0 2.823,0.156 0.094,0.156 10 false 4 2.719,1.625 2.833,1.771 0.115,0.146 10 true 5 1.01,0 1.125,0.156 0.115,0.156 10 false 6 0.927,1.656 1.052,1.813 0.125,0.156 10 true 7 2.156,0 2.25,0.146 0.094,0.146 10 false 8 1.542,0 1.719,0.146 0.177,0.146 10 false 10 1.521,1.646 1.698,1.792 0.177,0.146 10 true 11

Remove the 11 bearing cap bolts in the sequence shown in the illustration.


b.

Remove the 5 bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 15678A 21.REMOVE OIL CONTROL VALVE FILTER

Hide 11811 22.REMOVE NO. 1 CAMSHAFT BEARING

Hide 13511 23.REMOVE CAMSHAFT

a.

Remove the camshaft and No. 2 camshaft.


Hide 11821 24.REMOVE NO. 2 CAMSHAFT BEARING

Hide 13801 25.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 valve rocker arms from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 26.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjusters from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 27.REMOVE VALVE STEM CAP

a.

Remove the 16 valve stem caps from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 11101 28.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A196908N12
1.531,0.26 1.635,0.406 0.104,0.146 10 false 9 0.583,1.635 0.677,1.792 0.094,0.156 10 true 1 2.448,0.26 2.542,0.438 0.094,0.177 10 false 2 0.615,0.25 0.729,0.396 0.115,0.146 10 false 3 2.479,1.635 2.573,1.792 0.094,0.156 10 true 4 1.052,1.635 1.167,1.781 0.115,0.146 10 true 5 1.979,0.26 2.094,0.417 0.115,0.156 10 false 6 1.073,0.271 1.198,0.427 0.125,0.156 10 false 7 1.99,1.625 2.083,1.771 0.094,0.146 10 true 8 1.479,1.646 1.656,1.792 0.177,0.146 10 true 10

Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

HINT:

Be sure to keep the removed parts separate for each installation position.


NOTICE:
·

Be careful not to drop washers into the cylinder head.

·

Head warpage or cracking could result from removing bolts in the incorrect order.




b.

Remove the cylinder head.


Hide 11115 29.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block.