Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL PRESSURE REGULATOR
RM19V0EQ _51 Engine / Hybrid System _014575 2AR-FE FUEL _0073937 FUEL PRESSURE REGULATOR A

2AR-FE FUEL  FUEL PRESSURE REGULATOR  REMOVAL  


PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 83320 2.REMOVE FUEL SENDER GAUGE ASSEMBLY

Hide 23221 3.REMOVE FUEL PUMP

a.
A136231

Disconnect the fuel pump harness connectors from the fuel suction plate.


b.
A136234
1.719,1.979 1.073,1.979 false 0.865,1.885 1.042,2.042 0.177,0.156 10 *1
*1 E-ring


Using needle nose pliers, remove the E-ring.


c.
A211200
1.74,0.531 1.354,0.156 1.354,0.156 1.229,0.156 false 1.052,0.083 1.24,0.25 0.188,0.167 10 *1
*1 Tube


Disengage the 4 claws of the No. 1 fuel suction support and remove the lower fuel tank case sub-assembly from the fuel suction plate with the fuel filter.


d.

Remove the spring from the fuel suction plate.

NOTICE:

Do not do anything which may separate the fuel tube from either the fuel suction plate or fuel filter assembly, such as applying excessive force to the tube.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM>PRECAUTION



e.
A255954

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the No. 1 fuel suction support.


f.
A296957
2.177,0.427 2.583,0.427 false 3.01,1.896 3.01,1.542 false 2.625,0.365 2.938,0.521 0.313,0.156 10 *1 2.938,1.958 3.25,2.115 0.313,0.156 10 *2
*1 Fuel Filter
*2 Suction Filter


Using a screwdriver with its tip wrapped in protective tape, disengage the 5 claws, and remove the fuel pump from the fuel filter.

NOTICE:
·

Do not damage the fuel filter.

·

Do not remove the suction filter.

·

Do not use either the fuel pump or the suction filter if the suction filter is removed from the fuel pump.




g.
A192528

Disconnect the fuel pump harness connector.


h.
A192533
0.927,4.021 1,4.156 1,4.156 1.24,4.156 false 2.219,0.656 2.417,0.458 2.417,0.458 2.583,0.458 false 2.229,0.875 2.625,0.875 false 2.635,0.396 2.833,0.604 0.198,0.208 10 *1 2.646,0.781 2.833,1.135 0.188,0.354 10 *2 1.948,2.24 2.125,2.469 0.177,0.229 10 *a 1.906,1.656 2.083,1.813 0.177,0.156 10 *a 1.281,4.083 1.469,4.271 0.188,0.188 10 *1
*1 O-ring
*2 Spacer
*a 5.0 mm (0.197 in.)


Remove the O-ring and spacer from the fuel pump.

NOTICE:

Be careful not to damage the sealing surface.


HINT:

If the O-ring still remains in the fuel filter, remove it using a wire tip (1 mm diameter) that is formed as shown in the illustration.



Hide 23280J 4.REMOVE FUEL PRESSURE REGULATOR ASSEMBLY

a.
A136235

Using a screwdriver with its tip wrapped in protective tape, remove the fuel pressure regulator assembly from the fuel filter.

NOTICE:

Slowly pull out the fuel pressure regulator assembly because the O-ring is firmly installed between the fuel pressure regulator assembly and the fuel filter.



b.
A148186
1.583,0.646 1.583,0.427 1.583,0.427 0.625,0.427 false 0.927,1.396 0.927,0.427 false 0.427,0.344 0.604,0.479 0.177,0.135 10 *1
*1 O-ring


Remove the 2 O-rings from the pressure regulator assembly.