Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL PUMP
RM19V0EQ _51 Engine / Hybrid System _014575 2AR-FE FUEL _0073939 FUEL PUMP A

2AR-FE FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

Hide 5.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

Hide 72693 6.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fixed Seat Type)

Hide 72693 7.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

Hide 58325E 8.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A254977

Remove the rear floor service hole cover.


b.

Disconnect the fuel pump connector.


Hide 77209B 9.DISCONNECT FUEL PUMP TUBE SUB-ASSEMBLY

a.
A255953C01
2.417,3.375 2.635,3.156 2.635,3.156 2.708,3.156 false 2.115,2.885 2.313,2.688 2.313,2.688 2.417,2.688 false 1.385,2.885 1.198,2.698 1.198,2.698 1.094,2.698 false 1.844,3.688 1.354,3.688 false 1.844,3.542 1.635,3.542 1.635,3.542 1.635,3.677 false 2.365,3.552 2.552,3.76 2.552,3.76 2.625,3.76 false 2.104,1.073 1.583,0.563 1.583,0.563 1.479,0.563 false 2.76,3.052 2.938,3.229 0.177,0.177 10 false *1 0.917,2.594 1.094,2.771 0.177,0.177 10 false *3 2.49,2.583 2.667,2.76 0.177,0.177 10 false *2 1.208,3.615 1.385,3.792 0.177,0.177 10 false *4 2.688,3.677 2.865,3.854 0.177,0.177 10 false *5 1.323,0.479 1.5,0.656 0.177,0.177 10 false *1
*1 Tube Joint Clip
*2 Fuel Tube Joint
*3 Fuel Pump Tube
*4 O-ring
*5 Fuel Suction Plate


Remove the tube joint clip, and pull out the fuel pump tube.

NOTICE:
·

Remove any dirt or foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube joint has O-rings that seal the pipe.

·

Only disconnect the fuel tube joint by hand.

·

Do not forcibly bend, twist or turn the fuel pump tube.

·

Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.

·

If the fuel tube joint and fuel suction plate are stuck, push and pull to release them.




Hide 77168A 10.REMOVE FUEL TANK VENT TUBE SET PLATE

a.
A129480

Remove the 8 bolts and set plate.


Hide 77020A 11.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A139190

Remove the fuel suction tube with pump and gauge assembly from the fuel tank.

NOTICE:
·

Do not damage the suction filter.

·

Make sure that the fuel sender gauge arm does not bend.




b.
A136023C01
1.49,0.49 1.073,0.521 false 0.885,0.438 1.063,0.625 0.177,0.188 10 *1
*1 Fuel Suction Tube Set Gasket


Remove the fuel suction tube set gasket from the fuel suction tube assembly.