Home › Engine / Hybrid System › 2AR-FE LUBRICATION › OIL AND OIL FILTER
RM19V0EQ _51 Engine / Hybrid System _014579 2AR-FE LUBRICATION _0073962 OIL AND OIL FILTER A

2AR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


c.

Clean the oil pan drain plug and install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15620 2.REMOVE OIL FILTER CAP ASSEMBLY

a.
A204919
1.688,0.438 1.427,0.438 1.427,0.438 1.135,0.635 false 2.896,1.125 2.719,1.125 2.719,1.125 2.448,1.365 false 1.792,0.344 2.167,0.531 0.375,0.188 10 *1 3,1.052 3.229,1.333 0.229,0.281 10 *2
*1 Pipe
*2 Hose


Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.


b.
A196672

Remove the oil filter drain plug from the oil filter cap.


c.
A196673
2.99,3.042 2.771,3.042 2.771,3.042 2.771,2.844 false 2.615,2.74 2.417,2.74 2.417,2.74 2.417,2.875 false 2.865,1.792 2.698,1.792 2.698,1.792 2.573,2.333 false 1.958,2.604 1.958,2.458 1.958,2.458 2.208,2.458 false 3.042,2.958 3.25,3.167 0.208,0.208 10 *4 2.365,2.906 2.583,3.115 0.219,0.208 10 *3 2.917,1.74 3.156,1.938 0.24,0.198 10 *1 1.885,2.667 2.063,2.833 0.177,0.167 10 *2
*1 Valve
*2 Cap
*3 O-ring
*4 Pipe


Install the pipe to the oil filter cap.

NOTICE:

If the O-ring is removed with the drain plug, install the O-ring together with the pipe.


HINT:

Use a container to catch the draining oil.



d.
A196674

Check that the oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.


e.
A215914
0.594,0.708 0.813,0.708 0.813,0.708 1.5,1.24 false 2.813,1.146 2.677,1.146 2.677,1.146 2.448,1.385 false 2.885,1.063 3.281,1.281 0.396,0.219 10 SST 0.365,0.646 0.615,0.885 0.25,0.24 10 *1
*1 Oil Filter Bracket Clip


Using SST, remove the oil filter cap.

SST
09228-06501  

NOTICE:

Do not remove the oil filter bracket clip.



f.
A196675
0.635,0.271 0.865,0.271 0.865,0.271 1.135,0.438 false 2.917,1.323 2.719,1.323 2.719,1.323 2.25,1.615 false 2.906,0.781 2.688,0.781 2.688,0.781 2.438,1.115 false 0.417,0.219 0.656,0.458 0.24,0.24 10 *1 3,1.26 3.24,1.458 0.24,0.198 10 *2 2.979,0.708 3.229,0.958 0.25,0.25 10 *3
*1 Oil Filter Element
*2 Oil Filter Cap
*3 O-ring


Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Be sure to remove the O-ring by hand, without using any tools, to prevent damage to the O-ring groove.



Hide 15620 3.INSTALL OIL FILTER CAP ASSEMBLY

a.

Clean the inside of the oil filter cap, threads and O-ring groove.


b.
A196675
0.635,0.271 0.865,0.271 0.865,0.271 1.135,0.438 false 2.917,1.323 2.719,1.323 2.719,1.323 2.25,1.615 false 2.906,0.781 2.688,0.781 2.688,0.781 2.438,1.115 false 0.417,0.219 0.656,0.458 0.24,0.24 10 *1 3,1.26 3.24,1.458 0.24,0.198 10 *2 2.979,0.708 3.229,0.958 0.25,0.25 10 *3
*1 Oil Filter Element
*2 Oil Filter Cap
*3 O-ring


Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.


c.

Set a new oil filter element into the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

NOTICE:

Make sure that the O-ring does not get caught between the parts.



f.
A194917
1.021,3.402 1.27,3.606 0.249,0.205 10 *a 2.607,1.012 2.902,1.155 0.295,0.142 10 SST 1.855,1.344 2.559,1.111 false 1.596,3.765 1.225,3.505 false
*a No Clearance


Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Make sure that the oil filter is installed securely as shown in the illustration.



g.
A194918
2.417,1.49 2.865,1.667 false 2.26,1.406 2.49,1.615 0.229,0.208 10 false *1
*1 O-ring


Apply a small amount of engine oil to a new O-ring, and install it to the oil filter cap.

NOTICE:

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.



h.

Install the oil filter drain plug.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Be careful that the O-ring does not get caught between any surrounding parts.



Hide 4.ADD ENGINE OIL

a.

Add new oil.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)

API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil


·

0W-20


·

5W-20


·

5W-30


·

10W-30


API grade SL, SM or SN multigrade engine oil
·

15W-40


·

20W-50




Standard Capacity:
Item Specified Condition
Drain and refill (with oil filter change) 4.4 liters (4.6 US qts, 3.9 Imp. qts)
Drain and refill (without oil filter change) 4.0 liters (4.2 US qts, 3.5 Imp. qts)
Dry fill 5.3 liters (5.6 US qts, 4.7 Imp. qts)



b.

Install the oil filler cap.


Hide 5.INSPECT FOR OIL LEAK