Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE FLUID
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073974 AUTOMATIC TRANSAXLE FLUID A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE FLUID  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE AUTOMATIC TRANSAXLE FLUID

a.

Lift the vehicle. [*1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.

Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.


c.
C201682

Remove the refill plug and gasket from the automatic transaxle assembly. [*2]


d.
C201683
1.506,2.847 1.656,2.997 0.15,0.15 10 *1 1.506,3.683 1.667,3.835 0.161,0.152 10 *3 1.506,3.333 1.666,3.489 0.16,0.155 10 *2 1.468,2.927 0.981,2.927 false 1.468,3.42 1.009,3.42 false 1.468,3.763 0.956,3.763 false
*1 No. 1 Transmission Oil Filler Tube
*2 Overflow Plug
*3 Hexagon Socket Wrench


Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly. [*3]


e.
C201684
1.208,2.677 0.833,2.677 false 0.583,3.969 0.396,3.969 0.396,3.969 0.688,3.167 false 1.208,3.219 0.833,3.219 false 1.219,2.594 1.375,2.76 0.156,0.167 10 false *1 1.219,3.135 1.385,3.302 0.167,0.167 10 false *2 0.646,3.885 0.979,4.177 0.333,0.292 10 false *a
*1 No. 1 Transmission Oil Filler Tube
*2 Hexagon Socket Wrench
*a Overflow Plug Hole


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil pan sub-assembly and drain the automatic transaxle fluid. [*4]


f.
C239510

Measure the amount of fluid drained. [*5]

HINT:

Add the same amount of fluid in step [*8].



g.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle oil pan sub-assembly. [*6]

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


h.
C201687

Temporarily install the gasket and the overflow plug. [*7]

HINT:

Reuse the old gasket as the plug will be removed again to adjust the fluid level.



i.
C239936

Add fluid to the refill hole using the same amount of fluid drained in step [*5]. [*8]

NOTICE:

Use Toyota Genuine ATF WS.



j.
C201682

Temporarily install the gasket and refill plug to avoid fluid spillage. [*9]

HINT:

Reuse the old gasket as the plug will be removed again to adjust the fluid level.



k.

Lower the vehicle. [*10]


l.

Start the engine. [*11]


m.

Slowly move the shift lever from P to D, then back to P (keep the shift lever in each position for approximately 3 seconds). [*12]

HINT:

Slowly move the shift lever to circulate the fluid through each part of the automatic transaxle assembly.



n.

Allow the engine to idle for 30 seconds to warm it up. [*13]


o.

Turn the ignition switch off. [*14]


p.

Repeat steps [*1] to [*14].


q.

Repeat steps [*1] to [*10].


Hide 2.ADJUST FLUID TEMPERATURE (for Using the intelligent tester)

Hide 3.ADJUST FLUID TEMPERATURE (for not Using the intelligent tester)