Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY › 2011.10–2015.04
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073977 VALVE BODY ASSEMBLY A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35418 1.INSTALL MANUAL VALVE

a.

Coat the manual valve with ATF.


b.

Install the manual valve into the transmission valve body assembly.


Hide 35148 2.INSTALL NO. 1 GOVERNOR APPLY GASKET

a.

Coat 2 new No. 1 governor apply gaskets with ATF.


b.

Install the 2 No. 1 governor apply gaskets onto the transaxle case sub-assembly.


Hide 35410 3.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C201704
3.063,1.385 3.323,1.656 0.26,0.271 10 false *a 0.073,2.156 0.344,2.385 0.271,0.229 10 false *a 1,2.417 1.208,2.719 0.208,0.302 10 true A 1.417,2.396 1.615,2.625 0.198,0.229 10 true A 1.74,2.438 1.917,2.646 0.177,0.208 10 true A 2.177,2.365 2.385,2.594 0.208,0.229 10 true A 1.115,0.385 1.354,0.635 0.24,0.25 10 false B 0.094,1.125 0.292,1.365 0.198,0.24 10 false C 0.771,0.375 1,0.594 0.229,0.219 10 false D 1.781,0.469 1.958,0.677 0.177,0.208 10 true A 2.865,1.396 3.115,1.625 0.25,0.229 10 false B 0.115,1.99 0.302,2.24 0.188,0.25 10 false B 0.76,2.552 0.948,2.781 0.188,0.229 10 true B
*a Positioning Bolt


Coat the O-ring of the transmission wire with ATF.


b.

Insert the pin of the manual valve lever into the groove on the end of the manual valve and install the transmission valve body assembly onto the automatic transaxle assembly with the 11 bolts.

Bolt Length
Bolt Length [mm (in.)]
A 25 (0.984)
B 30 (1.18)
C and D 35 (1.38)

Torque:
Bolt A, B, C : 11 N*m (110 kgf*cm, 8 ft.*lbf)
Bolt D : 9.6 N*m (98 kgf*cm, 85 in.*lbf)

NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and automatic transaxle assembly to interfere with each other.

·

First, temporarily tighten the bolts marked *a in the illustration because they are positioning bolts.




Hide 35330 4.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with ATF.


b.

Install the O-ring onto the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted.



c.

Install the valve body oil strainer assembly onto the transmission valve body assembly with the 2 bolts.

Torque:
9.6 N*m (98 kgf*cm, 85 in.*lbf)


Hide 35394 5.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
C201701C11
2.719,0.219 1.771,0.219 1.771,0.219 1.771,0.75 false 2.49,0.219 2.49,1.146 false 2.844,0.146 3.167,0.406 0.323,0.26 10 false *1
*1 Transmission Oil Cleaner Magnet


Install the 2 transmission oil cleaner magnets onto the automatic transaxle oil pan sub-assembly as shown in the illustration.


Hide 35168A 6.INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET

a.

Install a new automatic transaxle oil pan gasket onto the automatic transaxle oil pan sub-assembly.


Hide 35106D 7.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C202902

Install the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket onto the automatic transaxle assembly with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surface of the automatic transaxle assembly and automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket before installation.



b.
C202903

Clean and degrease the 2 bolts and the installation hole in the automatic transaxle assembly.


c.

Apply adhesive to 2 or 3 threads on the ends of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.

Install the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)