Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073981 AUTOMATIC TRANSAXLE ASSEMBLY A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C201725

Engage the splines of the input shaft and turbine runner.


b.
C201726

Engage the splines of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter assembly back approximately 10 mm and engage the splines while rotating the torque converter assembly.



c.
C201727

Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.


d.

Clean the torque converter assembly set bolt holes.


e.
C201728C04
0.813,0.469 0.938,0.469 0.938,0.469 1.063,0.854 false 2.375,0.698 2.375,0.906 false 2.521,1.333 2.698,1.333 false 1.198,2.427 1.198,2.927 false 2.302,0.938 2.552,1.229 0.25,0.292 10 false *a 2.313,1.25 2.583,1.542 0.271,0.292 10 false *b 0.625,0.385 0.792,0.573 0.167,0.188 10 false *a 1.125,2.979 1.385,3.271 0.26,0.292 10 false *b 2.146,0.354 2.354,0.625 0.208,0.271 10 false A
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure dimension A between the transaxle contact surface of the engine *a and the torque converter assembly contact surface of the drive plate *b.

NOTICE:

Make sure to deduct the thickness of the straightedge.



f.
C207515N06
2.448,0.292 2.719,0.594 0.271,0.302 10 false B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 35150 3.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Apply ATF to a new O-ring and install it to the transmission case plug assembly.


b.

Install the transmission case plug assembly to the automatic transaxle assembly.


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the automatic transaxle assembly with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 70 in.*lbf)


Hide 33823 5.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 35123A 6.INSTALL TRANSMISSION BREATHER SKIRT (w/o ATF Warmer)

a.

Install the clamp to the transmission breather skirt.


b.

Install the transmission breather skirt to the transaxle with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Install the breather plug hose to the transmission breather skirt.


Hide 12311A 7.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the automatic transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 33493A 8.INSTALL TRANSMISSION OIL COOLER (w/ ATF Warmer)

a.

Install the transmission oil cooler to the front engine mounting bracket with the 3 bolts.

Torque:
14 N*m (138 kgf*cm, 10 ft.*lbf)


b.

Install the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose.


Hide 30500 9.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C201731C03
0.91,1.045 1.099,1.234 0.189,0.188 10 *2 2.202,1.119 2.384,1.283 0.181,0.164 10 *1 1.112,1.139 1.445,1.139 false 1.808,1.206 2.178,1.206 false
*1 Torque Converter Assembly Centerpiece
*2 Crankshaft


Apply clutch spline grease to the round of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C239000N06
2.414,2.267 2.533,2.428 0.119,0.161 10 A 2.818,2.74 2.937,2.901 0.119,0.161 10 A 0.934,2.303 1.054,2.464 0.119,0.161 10 A 0.701,2.852 0.82,3.013 0.119,0.161 10 B 2.947,3.416 3.066,3.577 0.119,0.161 10 B 2.875,3.817 2.994,3.978 0.119,0.161 10 C 2.663,4.155 2.782,4.316 0.119,0.161 10 C 1.205,4.33 1.324,4.491 0.119,0.161 10 C 0.798,4.172 0.917,4.333 0.119,0.161 10 C

While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 9 bolts shown in the illustration.

Bolt Bolt Length Torque
A 55 mm (2.17 in.) 64 N*m (653 kgf*cm, 47 ft.*lbf)
B 50 mm (1.97 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
C 32 mm (1.26 in.) 44 N*m (449 kgf*cm, 32 ft.*lbf)
33 mm (1.30 in.) 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Confirm that the 2 knock pins are installed to the transaxle contact surface of the engine cylinder block before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter rotates.




Hide 10.INSTALL WIRE HARNESS

a.

Connect the 7 wire harness clamps and park/neutral position switch connector.


b.

Install the ground cable with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 82824 11.INSTALL WIRING HARNESS CONNECTOR

a.

Install the wiring harness connector to the automatic transaxle assembly.


b.
C238952N04
2.229,0.302 2.427,0.5 0.198,0.198 10 true 1 1.823,0.229 2.031,0.417 0.208,0.188 10 true 2

Install and tighten the 2 bolts in the order shown in the illustration.

Torque:
11 N*m (115 kgf*cm, 8 ft.*lbf)


c.
C247470

Connect the connector to the wiring harness connector.


d.

Turn the lock lever and secure the connector with the lock lever.


Hide 51100G 12.INSTALL FRONT FRAME ASSEMBLY

Hide 43420G 13.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43420 14.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 15.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

Hide 16.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 17.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION