Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › TORQUE CONVERTER AND DRIVE PLATE
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073983 TORQUE CONVERTER AND DRIVE PLATE G

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.

Inspect the one-way clutch.

i.
C151051
1.25,0.615 1.448,0.813 0.198,0.198 10 .
V100135

Difficult
V100136

Smooth


Press on the splines of the stator with a finger and rotate it. Check that it rotates smoothly when turned clockwise and rotates with difficulty when turned counterclockwise.

If necessary, clean the torque converter assembly and recheck the one-way clutch.

Replace the torque converter assembly if the one-way clutch still fails the inspection.



b.
C274827
0.104,0.104 0.417,0.302 0.313,0.198 10 *a
*a Sample showing maximum allowable amount of powder in ATF


Inspect the torque converter assembly.

If any of the following problems are present, replace the torque converter assembly.

Malfunction:
·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or locks in both directions.

·

The amount of powder in the ATF is more than the sample shown in the illustration (refer to the sample).


HINT:

The sample shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF that was removed from a torque converter assembly.



c.

Replace the ATF in the torque converter assembly.

HINT:

If the ATF is discolored or has a foul odor, stir the ATF in the torque converter assembly and drain it before replacing the ATF.



d.
C247084
0.167,0.188 0.583,0.563 0.417,0.375 10 false *A 0.177,2.542 0.583,2.885 0.406,0.344 10 false *B
*A w/ ATF Warmer
*B w/o ATF Warmer


Clean and check the oil cooler and oil pipe line.

HINT:
·

If the torque converter assembly is inspected or the ATF is replaced, it is necessary to clean the oil cooler and oil pipe line.

·

Apply compressed air of 196 kPa (2.0 kgf/ cm2, 28 psi) into the inlet hose.

·

If a large amount of powder is found in the ATF, add new ATF using a bucket pump and clean the oil cooler and oil pipe line again.

·

If the ATF is cloudy, inspect the oil cooler.




e.
D025368
1.729,1.885 2.208,1.865 false 2.26,1.76 2.448,1.958 0.188,0.198 10 *c 0.49,0.167 0.76,0.333 0.271,0.167 10 *a 1.531,0.167 1.802,0.333 0.271,0.167 10 *b
*a Correct
*b Incorrect
*c Bottom is damaged


Prevent deformation of the torque converter assembly and damage to the oil pump gear.

NOTICE:

Make sure that all of the bolts are the same length and that the specified bolts are used.


HINT:

If there is any damage to the tip of a bolt for the torque converter assembly or to the bottom of a bolt hole, replace the bolt and torque converter assembly.



Hide 2.INSPECT DRIVE PLATE

a.

Check the drive plate for damage.


b.
C247557
1.675,0.284 1.804,0.44 0.129,0.156 10 1 1.254,0.993 1.41,1.15 0.156,0.156 10 2 1.829,1.849 1.985,2.005 0.156,0.156 10 3 2.638,1.808 2.794,1.964 0.156,0.156 10 4 2.423,0.474 2.58,0.631 0.156,0.156 10 6 2.839,1.124 2.995,1.28 0.156,0.156 10 5
V100144

Measuring Point


Set up a dial indicator and measure the runout at the 6 areas on the drive plate surface that contact the torque converter assembly.

Maximum runout:

0.30 mm (0.0118 in.)


HINT:
·

If the runout is more than the maximum or the drive plate is damaged, replace the drive plate.

·

If installing a new drive plate, confirm that the spacers are oriented properly before tightening the bolts.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>REAR CRANKSHAFT OIL SEAL>INSTALLATION