Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › 2011.10–2013.07
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073930 REAR CRANKSHAFT OIL SEAL A

2AR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Apply MP grease to the lip of a new oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the oil seal.

·

Do not allow MP grease to contact the dust seal.




b.
A195810
1.292,1.354 1.99,1.927 true 2,1.927 1.854,1.188 true 2.073,1.875 2.479,2.052 0.406,0.177 10 SST

Using SST and a hammer, tap in the oil seal until its surface is flush with the edges of the cylinder block and crankcase.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Keep the lip of the oil seal free from foreign matter.

·

Do not tap in the oil seal at an angle.




Hide 13405 2.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

a.
A195875
1.375,1.26 0.854,1.26 false 1.292,0.781 1.146,0.781 1.146,0.781 1.146,1.26 false 0.49,1.177 0.823,1.333 0.333,0.156 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



b.

Clean the bolts and their installation holes.


c.
A192239C51
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A210160
1.948,0.469 2.063,0.615 0.115,0.146 10 false 8 1.99,1.625 2.104,1.771 0.115,0.146 10 false 7 1.531,0.646 1.646,0.792 0.115,0.146 10 false 6 2.406,1.448 2.521,1.594 0.115,0.146 10 false 5 1.365,1.063 1.479,1.208 0.115,0.146 10 false 4 2.542,1.052 2.656,1.198 0.115,0.146 10 false 3 1.542,1.479 1.656,1.625 0.115,0.146 10 false 2 2.365,0.635 2.479,0.781 0.115,0.146 10 false 1

Install the flywheel sub-assembly with the 8 bolts. Uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)


Hide 31250 3.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 4.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31210 5.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 32101 6.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)

a.
A195875
1.375,1.26 0.854,1.26 false 1.292,0.781 1.146,0.781 1.146,0.781 1.146,1.26 false 0.49,1.177 0.823,1.333 0.333,0.156 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



b.

Clean the bolts and their installation holes.


c.
A196850

Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



d.
A196851
2.354,0.979 2.198,0.688 false 1.854,2 1.708,1.708 false 2.385,1.021 2.563,1.188 0.177,0.167 10 false *2 1.865,2.031 2.042,2.198 0.177,0.167 10 false *1
*1 Drive Plate
*2 Rear Drive Plate Spacer
V100135

Transaxle Side


Install the drive plate and rear drive plate spacer onto the crankshaft.


e.
A192239C51
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A196849
1.938,0.333 2.031,0.49 0.094,0.156 10 true 1 1.938,1.719 2.031,1.896 0.094,0.177 10 true 2 1.281,1.052 1.396,1.198 0.115,0.146 10 true 3 2.656,1.042 2.75,1.198 0.094,0.156 10 true 4 1.469,0.552 1.583,0.698 0.115,0.146 10 true 5 2.438,1.521 2.552,1.677 0.115,0.156 10 true 6 2.417,0.552 2.542,0.708 0.125,0.156 10 true 7 1.469,1.531 1.563,1.677 0.094,0.146 10 true 8

Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.



Hide 7.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

Hide 31407B 8.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 9.INSPECT CLUTCH PIPE LINE

Hide 31407B 10.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 11.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

Hide 30300 12.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 30500 13.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)