1.INSTALL DIFFERENTIAL SIDE GEAR
Coat the 2 front differential side gears, 2 No. 1 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.
41342F
2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT
Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.
3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH
41342A
4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN
Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin.
Align the holes, and install the front differential pinion shaft straight pin.
Using a chisel and hammer, stake the differential case.
Stake the differential case after adjusting the backlash.
41311F
5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
Using SST and a press, install a new front differential case rear tapered roller bearing to the front differential case.
Do not damage the bearing cage during bearing inner race installation.
Using SST and a hammer, install a new front differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.
Ensure that there is no clearance between the bearing and transaxle case sub-assembly.
41311E
6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
Using SST and a press, install a new front differential case front tapered roller bearing to the front differential case.
Do not damage the bearing cage during bearing inner race installation.
Install the shim to the transaxle housing.
Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle housing.
Ensure that there is no clearance between the bearing and transaxle housing.
7.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD
Remove packing material from the contact surfaces between the transaxle housing and case.
Install the differential assembly to the transaxle case sub-assembly.
Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.
Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.
0.89 to 1.31 N*m (9.08 to 13.35 kgf*cm, 7.88 to 11.59 in.*lbf)
If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.
| Thickness | Thickness | Thickness | Thickness |
|---|---|---|---|
| 2.000 (0.0787) | 2.225 (0.0876) | 2.450 (0.0965) | 2.675 (0.105) |
| 2.025 (0.0797) | 2.250 (0.0886) | 2.475 (0.0974) | 2.700 (0.106) |
| 2.050 (0.0807) | 2.275 (0.0896) | 2.500 (0.0984) | 2.725 (0.107) |
| 2.075 (0.0817) | 2.300 (0.0906) | 2.525 (0.0994) | 2.750 (0.108) |
| 2.100 (0.0827) | 2.325 (0.0915) | 2.550 (0.100) | 2.775 (0.109) |
| 2.125 (0.0837) | 2.350 (0.0925) | 2.575 (0.101) | 2.800 (0.110) |
| 2.150 (0.0846) | 2.375 (0.0935) | 2.600 (0.102) | 2.825 (0.111) |
| 2.175 (0.0856) | 2.400 (0.0945) | 2.625 (0.103) | 2.850 (0.112) |
| 2.200 (0.0866) | 2.425 (0.0955) | 2.650 (0.104) | 2.875 (0.113) |
Remove the 20 bolts and the transaxle housing from the transaxle case sub-assembly.
Remove the front differential case from the transaxle case sub-assembly.
41221
8.INSTALL FRONT DIFFERENTIAL RING GEAR
| *a | 90 to 110°C |
Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).
Do not heat the ring gear to more than 110°C (230°F).
| *a | Matchmark |
Clean the contact surface of the front differential case.
Align the matchmarks, set the front differential ring gear to the front differential case.
Install the 12 bolts.
Tighten the bolts after the front differential ring gear has cooled down sufficiently.
Tighten the bolts evenly in a diagonal pattern using several steps.
31105H
9.INSTALL TRANSAXLE CASE OIL SEAL
Coat the lip of a new transaxle case oil seal with a small amount of MP grease.
Using SST and a hammer, tap in the transaxle case oil seal.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Check that the oil seal is installed in the correct direction.
31105D
10.INSTALL FRONT TRANSAXLE CASE OIL SEAL
Coat the lip of a new front transaxle case oil seal with a small amount of MP grease.
Using SST and a hammer, tap in the front transaxle case oil seal.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Check that the oil seal is installed in the correct direction.