Home › Drivetrain › CLUTCH › CLUTCH PEDAL › 2011.10–2013.07
RM19V0EQ _52 Drivetrain _014583 CLUTCH _0073991 CLUTCH PEDAL A

CLUTCH  CLUTCH PEDAL  INSTALLATION  


PROCEDURE

Hide 31453B 1.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING

a.
C287074C01
0.354,1.271 0.417,1.25 false
V100135

MP grease


Apply MP grease to the inside of a new clutch master cylinder push rod clevis bushing.


b.

Install the clutch master cylinder push rod clevis bushing to the clutch pedal sub-assembly.

HINT:

Install the clutch master cylinder push rod clevis bushing from the left side of the vehicle.



Hide 2.INSTALL CLUTCH PEDAL TURNOVER BUSHING

a.
C287075C01
2.083,0.875 2.125,0.854 false
V100135

MP grease


Apply MP grease to the inside of a new clutch pedal turnover bushing.


b.

Install the clutch pedal turnover bushing to the clutch pedal sub-assembly.


Hide 31301B 3.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.

Using needle-nose pliers, install the 2 No. 1 clutch pedal cushions to the clutch pedal sub-assembly.


Hide 31301C 4.INSTALL CLUTCH PEDAL BUSHING

a.
C287076C01
0.604,1.198 0.594,1.198 false
V100135

MP grease


Apply MP grease to the inner, outer and end surfaces of 2 new clutch pedal bushings.


b.

Install the clutch pedal shaft collar and 2 clutch pedal bushings to the clutch pedal sub-assembly.


Hide 31321 5.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31353 6.INSTALL CLUTCH PEDAL SPRING HOLDER

a.
C287077C01
1.281,1.063 1.365,1.031 false
V100135

MP grease


Apply MP grease to the inside of a new clutch pedal spring holder.


b.

Install the clutch pedal spring holder to the clutch pedal support sub-assembly.


Hide 7.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

Torque:
37 N*m (375 kgf*cm, 27 ft.*lbf)

HINT:
·

Install the bolt from the left side of the vehicle.

·

When installing the nut, keep the bolt from rotating.




Hide 31394A 8.INSTALL TORSION SPRING

a.
C287078C01
1.302,0.521 1.302,0.51 false
V100135

MP grease


Apply MP grease to the sliding portion of the torsion spring.


b.

Install the torsion spring.


Hide 88280A 9.INSTALL CLUTCH SWITCH ASSEMBLY (w/ Cruise Control System)

a.

Install the clutch switch assembly so that its end touches the No. 1 clutch pedal cushion.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



Hide 10.INSTALL CLUTCH PEDAL STOPPER BOLT (w/o Cruise Control System)

a.

Install the clutch pedal stopper bolt so that its end touches the clutch pedal cushion.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



Hide 11.INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

a.

Install the clutch pedal support sub-assembly to the vehicle with the 2 nuts and bolt.

Torque:
Bolt : 19 N*m (195 kgf*cm, 14 ft.*lbf)
Nut : 12 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 31453A 12.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS PIN

a.
C287079C01
0.802,0.396 0.854,0.385 false
V100135

MP grease


Apply MP grease to the contact surfaces of the clutch master cylinder push rod clevis pin and clutch master cylinder push rod clevis bushing.


b.

Connect the clutch master cylinder push rod clevis to the clutch pedal sub-assembly with the clutch master cylinder push rod clevis pin and a new clip.

HINT:

Install the clutch master cylinder push rod clevis pin from the left side of the vehicle.



Hide 13.CONNECT CONNECTOR (w/ Cruise Control System)

a.

Connect the clutch switch assembly connector.


Hide 83100 14.INSTALL COMBINATION METER ASSEMBLY

Hide 15.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY