Home › Drivetrain › CLUTCH › CLUTCH UNIT › 2011.10–2013.07
RM19V0EQ _52 Drivetrain _014583 CLUTCH _0073994 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust from the moving section could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C204661C01
1.052,3.479 1.052,3.615 false 1.25,2.698 1.708,2.698 false 2.667,1.583 2.875,1.583 false 2.927,1.51 3.333,1.781 0.406,0.271 10 false SST 0.927,3.656 1.323,3.927 0.396,0.271 10 false SST 1.031,2.625 1.323,2.927 0.292,0.302 10 false *1 2.167,3.292 2.51,3.573 0.344,0.281 10 false *a
*1 Clutch Disc
*a Flywheel Side


Insert SST into the clutch disc assembly, then insert them both into the flywheel sub-assembly.

SST
09301-00210  

NOTICE:

Insert the clutch disc assembly in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C204662C01
2.271,1.573 2.531,1.573 false 0.792,1.354 0.51,1.802 0.51,1.802 0.865,1.365 false 2.604,1.5 3.094,1.813 0.49,0.313 10 false SST 1.948,1.833 2.427,2.063 0.479,0.229 10 false 2, 5 1.292,1.906 1.573,2.125 0.281,0.219 10 false 6 2.469,0.969 2.75,1.229 0.281,0.26 10 false 8 2.073,0.417 2.781,0.667 0.708,0.25 10 true 1 (*a), 4 0.583,0.469 0.771,0.719 0.188,0.25 10 true 7 0.396,0.896 0.625,1.094 0.229,0.198 10 true 3 0.396,1.813 0.698,2.083 0.302,0.271 10 false *b
*a Temporarily
*b Matchmark


Align the matchmark on the clutch cover assembly with that on the flywheel sub-assembly.


b.

Following the procedure shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

SST
09301-00210  

Torque:
19 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the disc is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C204663

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Maximum non-alignment:

0.5 mm (0.0197 in.)



b.
C204664N01
2.698,0.906 2.458,0.906 2.458,0.906 2.281,1.458 false 2.771,0.833 3.198,1.083 0.427,0.25 10 false SST

If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 4.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

a.
C197022

Temporarily tighten the clutch release cylinder to bleeder tube onto a new clutch release with bearing cylinder assembly.


b.

Clean and degrease all installation surfaces for the clutch release with bearing cylinder assembly.


c.
C187781

Install the clutch release with bearing cylinder assembly with 3 new bolts.

Torque:
23 N*m (229 kgf*cm, 17 ft.*lbf)

NOTICE:
·

The clutch release with bearing cylinder and installation bolts cannot be reused and must be replaced with new ones.

·

Clean and degrease all installation surfaces and make sure that the clutch release with bearing cylinder fits securely with the transaxle during installation. The first bolt should be tightened by hand while holding the clutch release with bearing cylinder.

·

Ensure that none of the clutch disc spline grease adheres to the clutch release with bearing cylinder.

·

The clutch release with bearing cylinder cannot be disassembled.




d.
C199330

Install the clutch tube boot onto the front transaxle case.


e.
C204665

Temporarily tighten the clutch release cylinder to bleeder tube onto the clutch release bleeder sub-assembly.


f.

Temporarily tighten the 2 bolts and install the clutch release bleeder.


g.
C197021

Using a (10 mm) union nut wrench, install the clutch release cylinder to bleeder tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a union nut wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



h.
C196061C03
1.146,1.188 1.198,1.177 false
V100135

Toyota Genuine Clutch Spline Grease or equivalent


Apply clutch spline grease to the input shaft splines.

Sealant:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 31407B 5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C204665

Separate the clutch release cylinder to bleeder tube from the clutch release bleeder sub-assembly.


b.

Remove the 2 bolts and the clutch release bleeder sub-assembly.


Hide 6.INSPECT CLUTCH PIPE LINE

C248721N01
2.948,0.771 2.813,0.771 2.813,0.771 2.708,1.042 false 3.01,0.698 3.375,0.969 0.365,0.271 10 false SST

a.

Using SST, apply pressure of 0.1 MPa to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

SST
09992-00242  

If the pressure drops, replace the clutch release cylinder to bleeder tube.


Hide 31407B 7.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C204665

Temporarily tighten the clutch release cylinder to bleeder tube onto the clutch release bleeder sub-assembly.


b.

Install the 2 bolts and clutch release bleeder sub-assembly.

Torque:
17 N*m (170 kgf*cm, 12 ft.*lbf)


c.
C204656

Using a (10 mm) union nut wrench, install the clutch release cylinder to bleeder tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a union nut wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 8.INSTALL CLUTCH LINE

a.
C224568

Using a (10 mm) union nut wrench, install the clutch line.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a union nut wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Install the bolt and clutch line.

Torque:
Bolt Length 18 mm (0.709 in.) : 19 N*m (192 kgf*cm, 14 ft.*lbf)
Bolt Length 16 mm (0.630 in.) : 12 N*m (120 kgf*cm, 9 ft.*lbf)