Home › Drivetrain › EB62 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY › 2011.10–2013.07
RM19V0EQ _52 Drivetrain _014584 EB62 MANUAL TRANSMISSION / TRANSAXLE _0074001 MANUAL TRANSAXLE ASSEMBLY A

EB62 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust from the moving section could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


PROCEDURE

Hide 33403K 1.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.

Coat a new O-ring with gear oil.


b.

Install the O-ring onto the speedometer driven hole cover sub-assembly.


c.

Install the speedometer driven hole cover sub-assembly onto the front transaxle case with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C248141

Install the 2 wire harness clamp brackets with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 3.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

Hide 31407B 4.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 5.INSPECT CLUTCH PIPE LINE

Hide 31407B 6.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31484 7.INSTALL CLUTCH FLEXIBLE HOSE BRACKET

a.

Install the clutch flexible hose bracket with the bolt.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


b.

Install the clutch line to the clutch flexible hose bracket with the bolt.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 31490 8.INSTALL CLUTCH ACCUMULATOR ASSEMBLY

Hide 9.CONNECT CLUTCH LINE

Hide 12311A 10.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 30300 11.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.
C203276

Make sure that the knock pins are not loose, bent, damaged or scratched.


b.
C248139

Align the input shaft with the clutch disc and install the manual transaxle onto the engine.


c.

Temporarily tighten the manual transaxle assembly with the 10 bolts.

NOTICE:
·

Insert the dowel pins into the dowel holes securely so that the end face of the transaxle assembly fits close against the engine assembly before tightening the bolts.

·

Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle onto the engine with the contact surfaces of the engine and transaxle flat against each other.




d.
C248142
1.292,0.094 1.563,0.417 0.271,0.323 10 false 1 2.25,0.052 2.5,0.333 0.25,0.281 10 false 2 2.771,0.313 3.073,0.656 0.302,0.344 10 false 3

Fully tighten the 3 bolts in the sequence shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

HINT:
Bolt Bolt Length
1, 2 60 mm (2.36 in.)
3 74.5 mm (2.93 in.)



e.
C248143
1.021,0.198 1.354,0.469 0.333,0.271 10 false A 0.76,0.646 1.115,0.969 0.354,0.323 10 false A 2.979,0.865 3.281,1.188 0.302,0.323 10 false B 2.906,1.313 3.135,1.573 0.229,0.26 10 false C 2.698,1.667 2.938,1.958 0.24,0.292 10 false C 1.51,1.875 1.792,2.125 0.281,0.25 10 false C 1.104,1.729 1.344,1.979 0.24,0.25 10 false C

Fully tighten the 7 bolts.

Bolt Bolt Length Torque
A 60 mm (2.36 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
B 65 mm (2.56 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
C 32 mm (1.26 in.) 44 N*m (449 kgf*cm, 32 ft.*lbf)
33 mm (1.30 in.) 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Confirm that the 2 knock pins are installed to the transaxle contact surface of the engine cylinder block before installing the manual transaxle assembly.

·

Do not forcibly pry on the manual transaxle assembly.




Hide 12372A 12.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH

Hide 12361A 13.TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR

Hide 51100G 14.INSTALL FRONT FRAME ASSEMBLY

Hide 43420G 15.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43420 16.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 17.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

Hide 18.CONNECT WIRE HARNESS

a.

Connect the 2 connectors and install the cable with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the wire harness to the manual transaxle assembly with the 2 clamps and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 19.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE