1.REMOVE MANUAL TRANSMISSION FILLER PLUG
Remove the manual transmission filler plug and gasket from the manual transmission case sub-assembly.
2.REMOVE MANUAL TRANSMISSION DRAIN PLUG
Remove the manual transmission drain plug and gasket from the front transaxle case.
33111C
3.REMOVE TRANSMISSION CASE PLUG
Remove the transmission case plug and gasket from the manual transmission case sub-assembly.
84210
4.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
Using a (27 mm) deep socket wrench, remove the back-up light switch assembly and gasket from the manual transmission case sub-assembly.
5.REMOVE CONTROL CABLE BRACKET
Remove the 3 bolts and control cable bracket from the manual transmission case sub-assembly.
31478
6.REMOVE RELEASE CYLINDER BLEEDER PLUG CAP
Remove the release cylinder bleeder plug cap from the release cylinder bleeder plug.
31477
7.REMOVE RELEASE CYLINDER BLEEDER PLUG
Remove the release cylinder bleeder plug from the clutch release bleeder sub-assembly.
31407B
8.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
31400
9.REMOVE CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
31483
10.REMOVE CLUTCH RELEASE CYLINDER TO BLEEDER TUBE
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
30300
11.SECURE MANUAL TRANSAXLE ASSEMBLY
Place the manual transaxle assembly on wooden blocks.
33451H
12.REMOVE REVERSE IDLER GEAR SHAFT BOLT
Remove the reverse idler gear shaft bolt and gasket from the manual transmission case sub-assembly.
33292A
13.REMOVE LOCK BALL PIN
Using a (10 mm) hexagon socket wrench, remove the shift and select lever shaft straight screw with head plug from the manual transmission case sub-assembly.
Using a magnet hand, remove the shift and select lever shaft compression spring and lock ball pin from the manual transmission case sub-assembly.
Using a (10 mm) hexagon socket wrench, remove the shift and select lever shaft straight screw with head plug from the manual transmission case sub-assembly.
Using a magnet hand, remove the shift and select lever shaft compression spring and lock ball pin from the manual transmission case sub-assembly.
33275C
14.REMOVE SHIFT DETENT BALL
Using a (6 mm) hexagon socket wrench, remove the shift detent ball plug from the manual transmission case sub-assembly.
Using a magnet hand, remove the shift detent ball compression spring and shift detent ball from the manual transmission case sub-assembly.
Using a (6 mm), hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case sub-assembly.
Using a magnet hand, remove the 2 shift detent ball compression springs and 2 shift detent balls from the manual transmission case sub-assembly.
33253F
15.REMOVE OUTER SHIFT LEVER E RING
Remove the outer shift lever E ring from the outer No. 1 shift lever.
33101
16.REMOVE MANUAL TRANSMISSION CASE SUB-ASSEMBLY
Remove the 17 bolts.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, separate the manual transmission case sub-assembly from the front transaxle case.
Do not damage the manual transmission case sub-assembly.
Turn the outer No. 1 shift lever clockwise until it comes into contact with the boss.
Push the outer No. 1 shift lever and remove the manual transmission case sub-assembly.
33402
17.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY
Remove the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft from the front transaxle case.
33211
18.REMOVE REVERSE SHIFT FORK
Turn the reverse shift fork clockwise and remove it from the front transaxle case.
Using a (5 mm) pin punch and hammer, tap out the reverse shift fork slotted spring pin.
Remove the reverse shift fork from the No. 4 gear shift fork shaft.
33240
19.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY
Using a (6 mm) hexagon socket wrench, remove the 2 bolts and reverse shift arm bracket assembly from the front transaxle case.
20.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY
Turn the shift and select lever shaft assembly clockwise and remove it from the front transaxle case.
Remove the shift interlock plate.
21.REMOVE OUTER SELECT LEVER
Remove the inner select lever set bolt.
Remove the outer select lever and inner select lever from the front transaxle case.
33257C
22.REMOVE OUTER SELECT LEVER OIL SEAL
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, remove the outer select lever oil seal from the front transaxle case.
Do not damage the installation surfaces.
23.REMOVE INPUT SHAFT ASSEMBLY
Remove the input shaft assembly, output shaft assembly and 2 gear shift fork shaft assemblies from the front transaxle case.
Remove the output shaft assembly together with the No. 1 gear shift fork shaft assembly from the input shaft assembly.
Remove the No. 1 gear shift fork shaft assembly from the output shaft assembly.
Remove the No. 2 gear shift fork shaft assembly from the input shaft assembly.
24.REMOVE DIFFERENTIAL CASE ASSEMBLY
Remove the differential case assembly from the front transaxle case.
41311E
25.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential oil baffle from the front transaxle case.
| *a | Turn |
| *b | Hold |
Using SST, remove the front differential case front tapered roller bearing from the differential case assembly.
41311F
26.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear plate shim from the manual transmission case.
| *a | Turn |
| *b | Hold |
Using SST, remove the front differential case rear tapered roller bearing from the differential case assembly.
33449B
27.REMOVE TRANSMISSION MAGNET
Remove the transmission magnet from the front transaxle case.
33101J
28.REMOVE BREATHER PLUG
Remove the breather plug from the front transaxle case.
33321N
29.REMOVE FRONT OUTPUT SHAFT BEARING
Using SST, tap the front output shaft bearing (outer race) from the front transaxle case.
Remove the output shaft cover from the front transaxle case.
31105D
30.REMOVE FRONT TRANSAXLE CASE OIL SEAL
Using SST, tap out the front transaxle case oil seal from the front transaxle case.
31105C
31.REMOVE TRANSAXLE CASE STRAIGHT PIN
Remove the 5 transaxle case straight pins from the front transaxle case.
33311K
32.REMOVE REAR INPUT SHAFT BEARING SHIM
Remove the rear input shaft bearing shim from the manual transmission case sub-assembly.
33137
33.REMOVE INPUT SHAFT COVER
Remove the input shaft cover from the manual transmission case sub-assembly.
34.REMOVE NO. 1 OIL RECEIVER PIPE
Remove the No. 1 oil receiver pipe from the manual transmission case sub-assembly.
35.REMOVE OUTER NO. 1 SHIFT LEVER
Using a (5 mm) pin punch and hammer, tap out the inner shift lever slotted spring pin.
When removing the inner shift lever slotted spring pin, align the pin with the hole in the lock ball assembly.
Remove the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever from the manual transmission case sub-assembly.
33253H
36.REMOVE OUTER SHIFT LEVER OIL SEAL
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, remove the outer shift lever oil seal from the manual transmission case sub-assembly.
Do not damage the installation surfaces.
33321A
37.REMOVE REAR OUTPUT SHAFT BEARING
Using SST, remove the rear output shaft bearing (outer race) and rear output shaft bearing shim from the manual transmission case sub-assembly.
33111Q
38.REMOVE TRANSMISSION CASE OIL SEAL
Using SST, remove the transmission case oil seal from the manual transmission case sub-assembly.
31105H
39.REMOVE TRANSAXLE CASE OIL SEAL
Using SST, remove the transaxle case oil seal from the front transaxle case.