Home › Drivetrain › EB62 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT › 2011.10–2013.07
RM19V0EQ _52 Drivetrain _014584 EB62 MANUAL TRANSMISSION / TRANSAXLE _0074002 MANUAL TRANSAXLE UNIT A

EB62 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 41311E 1.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C200155
0.49,2.854 1.063,2.854 false 1.073,2.99 0.656,2.99 0.656,2.99 0.656,2.854 false 0.781,0.542 1.646,0.542 1.646,0.542 2.25,1.25 false 2.115,1.333 1.396,0.542 false 1.823,1.354 1.146,0.542 false 0.156,2.781 0.646,3.115 0.49,0.333 10 false SST 0.385,0.469 0.854,0.813 0.469,0.344 10 false SST

Using SST and a press, press in a new front differential case front tapered roller bearing to the differential case.

SST
09316-20011  
09950-60010  (09951-00580, 09952-06010)
09950-60020  (09951-00910)
09950-40011  (09957-04010)
09950-70010  (09951-07100)


b.
C224593
1.26,0.615 1.969,0.365 false 1.24,0.729 1.99,0.854 false 2.031,0.25 2.333,0.542 0.302,0.292 10 false *a 2.083,0.802 2.438,1.083 0.354,0.281 10 false *b
*a Groove
*b Key


Install the front differential oil baffle to the front transaxle case.

NOTICE:

Insert the front differential oil baffle key into the front transaxle case groove.



c.
C207939
2.563,1.365 2.771,1.021 2.771,1.021 2.938,1.021 false 2.635,1.927 2.885,2.365 2.885,2.365 2.99,2.365 false 0.708,0.479 0.198,0.479 0.198,0.479 0.198,1.677 false 0.375,0.698 0.198,0.698 true 0.458,0.844 0.198,0.844 true 1.219,0.906 1.219,0.406 1.219,0.406 1.313,0.406 false 0.906,1.188 1.094,1.188 1.094,1.188 1.094,1.063 false 3.01,0.948 3.385,1.333 0.375,0.385 10 false SST 3.063,2.281 3.417,2.594 0.354,0.313 10 false SST 0.094,1.729 0.563,2.063 0.469,0.333 10 false SST 1.354,0.323 1.802,0.688 0.448,0.365 10 false *1 0.719,1.115 1,1.438 0.281,0.323 10 false *2
*1 Front Differential Case Front Tapered Roller Bearing (Outer Race)
*2 Front Differential Oil Baffle


Using SST and a press, press in a new front differential case front tapered roller bearing (outer race) to the front transaxle case.

SST
09950-60010  (09952-06010)
09950-60020  (09951-00780, 09951-00890)
09950-70010  (09951-07100)


Hide 41311F 2.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C200157
0.906,0.656 1.76,0.656 1.76,0.656 2.302,1.521 false 1.292,0.656 1.865,1.635 false 1.625,0.656 2.198,1.604 false 0.531,2.583 0.938,2.583 false 0.948,2.979 0.823,2.979 0.823,2.979 0.823,2.583 false 0.583,0.594 1.188,1.073 0.604,0.479 10 false SST 0.208,2.521 0.802,2.917 0.594,0.396 10 false SST

Using SST and a press, press in a new front differential case rear tapered roller bearing to the differential case.

SST
09316-20011  
09950-60010  (09951-00580, 09952-06010)
09950-60020  (09951-00910)
09950-40011  (09957-04010)
09950-70010  (09951-07100)


b.
C200158
2.073,0.458 1.208,0.458 false 2.115,0.917 1.542,0.917 1.542,0.917 1.542,0.458 false 3.063,0.354 2.958,0.354 2.958,0.354 2.844,0.667 false 2.833,0.75 2.948,1.031 2.948,1.031 3.073,1.031 false 0.865,0.385 1.323,0.646 0.458,0.26 10 false SST 3.135,0.271 3.365,0.51 0.229,0.24 10 false *1 3.125,0.948 3.375,1.198 0.25,0.25 10 false *2
*1 Front Differential Case Rear Tapered Roller Bearing (Outer Race)
*2 Front Differential Case Rear Plate Shim


Using SST, install a new front differential case rear tapered roller bearing (outer race) together with the front differential case rear plate shim as shown in the illustration.

SST
09950-60020  (09951-00770, 09951-00890)


Hide 3.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.
C202182

Coat the differential case assembly with gear oil and install it to the front transaxle case.


b.
C203963

Install the manual transmission case sub-assembly with the 17 bolts.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C200159
0.927,1.083 1.781,0.333 1.781,0.333 1.969,0.333 true 2.052,0.26 2.792,0.615 0.74,0.354 10 false SST

Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-50010  


d.

Using SST and a torque wrench, measure the preload.

SST
09564-50010  

Standard preload (at starting):
New bearing:

1.50 to 2.30 N*m (15 to 23 kgf*cm, 13 to 20 in.*lbf)

Used bearing:

0.24 to 0.37 N*m (2.4 to 3.8 kgf*cm, 2.1 to 3.3 in.*lbf)


If the preload is not as specified, replace the front differential case rear plate shim with one of a different thickness. Use the table below to select a front differential case rear plate shim which will ensure that the preload is within the specification.

Standard Shim Thickness:
Mark Specified Condition Mark Specified Condition
A 2.05 mm (0.0807 in.) K 2.50 mm (0.0984 in.)
B 2.10 mm (0.0827 in.) L 2.55 mm (0.100 in.)
C 2.15 mm (0.0846 in.) M 2.60 mm (0.102 in.)
D 2.20 mm (0.0866 in.) N 2.65 mm (0.104 in.)
E 2.25 mm (0.0886 in.) P 2.70 mm (0.106 in.)
F 2.30 mm (0.0906 in.) Q 2.75 mm (0.108 in.)
G 2.35 mm (0.0925 in.) R 2.80 mm (0.110 in.)
H 2.40 mm (0.0945 in.) S 2.85 mm (0.112 in.)
J 2.45 mm (0.0965 in.) T 2.90 mm (0.114 in.)


HINT:
·

Select a thicker plate shim to increase the preload, or a thinner plate shim to decrease the preload.

·

Make a memo as the torque values will be needed for the Adjust Output Shaft Bearing Preload procedure.




e.

Remove the 17 bolts and manual transmission case sub-assembly.


f.

Remove the differential case from the front transaxle case.


g.

Replace the installed front differential case rear plate shim with the one selected above.


Hide 33321N 4.INSTALL FRONT OUTPUT SHAFT BEARING

a.
C202188
1.177,1.594 1.313,1.594 1.313,1.594 1.458,0.896 true 1.854,1.708 1.719,1.708 1.719,1.708 1.542,1.417 true 0.99,1.5 1.229,1.75 0.24,0.25 10 true *a 1.906,1.615 2.25,1.969 0.344,0.354 10 true *b
*a Output Shaft Cover Key
*b Front Transaxle Case Groove


Install the output shaft cover onto the front transaxle case.

NOTICE:

Insert the output shaft cover key into the front transaxle case groove.



b.
C200161
0.948,0.99 0.948,0.448 0.948,0.448 0.656,0.448 false 0.885,1.063 0.885,0.448 false 2.094,2.115 2.698,0.927 false 2.094,1.656 2.458,0.927 2.458,0.927 2.813,0.927 false 0.75,1.167 0.469,1.167 true 1.323,1.25 1.323,0.438 1.323,0.438 1.448,0.438 false 0.323,0.375 0.76,0.604 0.438,0.229 10 false SST 2.896,0.865 3.271,1.167 0.375,0.302 10 false SST 0.26,1.094 0.542,1.396 0.281,0.302 10 false *1 1.5,0.365 1.813,0.615 0.313,0.25 10 false *2
*1 Front Output Shaft Bearing (Outer Race)
*2 Output Shaft Cover


Using SST and a press, press in a new front output shaft bearing (outer race) to the front transaxle case.

SST
09950-60010  (09951-00620, 09952-06010)
09950-60020  (09951-00710)
09950-70010  (09951-07100)


Hide 33321A 5.INSTALL REAR OUTPUT SHAFT BEARING

a.
C200162
1.969,1.229 2.313,1.229 false 2.156,0.667 2.469,0.667 2.469,0.667 2.469,1.052 false 2.396,1.125 2.396,0.667 false 0.469,2.031 1.063,2.031 false 1.094,2.208 0.75,2.208 0.75,2.208 0.75,2.031 false 2.969,1.323 2.969,1.469 2.969,1.469 2.833,1.469 false 1.844,0.583 2.24,0.833 0.396,0.25 10 false SST 0.146,1.948 0.573,2.177 0.427,0.229 10 true SST 1.74,1.146 2.031,1.406 0.292,0.26 10 false *1 2.625,1.375 2.833,1.552 0.208,0.177 10 true *2
*1 Rear Output Shaft Bearing (Outer Race)
*2 Rear Output Shaft Bearing Shim


Using SST and a press, press in a new rear output shaft bearing (outer race) together with the rear output shaft bearing shim to the manual transmission case.

SST
09950-60010  (09951-00490, 09951-00620, 09952-06010)
09950-70010  (09951-07150)


Hide 6.ADJUST OUTPUT SHAFT BEARING PRELOAD

a.
C202182

Coat the differential case assembly with gear oil and install it to the front transaxle case.


b.
C200163

Coat the output shaft assembly with gear oil and install it to the front transaxle case.


c.
C203963

Install the manual transmission case sub-assembly with the 17 bolts.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


d.
C200164
1.656,0.365 2.115,0.365 false 0.927,1.698 2.146,1.698 2.146,1.698 2.146,1.865 false 2.177,0.292 2.458,0.594 0.281,0.302 10 false *1 2.021,1.917 2.448,2.167 0.427,0.25 10 false SST
*1 Rear Output Shaft Bearing Shim


Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-50010  


e.

Using SST and a torque wrench, measure the preload (value A). Calculate the rear output shaft bearing shim value using the following formula.

SST
09564-50010  

Formula:

Value A - Differential side bearing preload = Output shaft bearing preload


Preload (at starting):
New bearing:

2.80 to 5.60 N*m (29 to 57 kgf*cm, 25 to 50 in.*lbf)

Used bearing:

2.31 to 4.62 N*m (24 to 47 kgf*cm, 20 to 41 in.*lbf)


If the preload is not as specified, replace the rear output shaft bearing shim with one of a different thickness. Use the table below to select a rear output shaft bearing shim which will ensure that the preload is within the specification.

Standard Bearing Shim Thickness:
Mark Specified Condition Mark Specified Condition
A 1.30 mm (0.0511 in.) P 1.95 mm (0.0768 in.)
B 1.35 mm (0.0531 in.) Q 2.00 mm (0.0787 in.)
C 1.40 mm (0.0551 in.) R 2.05 mm (0.0807 in.)
D 1.45 mm (0.0571 in.) S 2.10 mm (0.0827 in.)
E 1.50 mm (0.0591 in.) T 2.15 mm (0.0846 in.)
F 1.55 mm (0.0610 in.) U 2.20 mm (0.0866 in.)
G 1.60 mm (0.0630 in.) V 2.25 mm (0.0886 in.)
H 1.65 mm (0.0650 in.) W 2.30 mm (0.0906 in.)
J 1.70 mm (0.0669 in.) X 2.35 mm (0.0925 in.)
K 1.75 mm (0.0689 in.) Y 2.40 mm (0.0945 in.)
L 1.80 mm (0.0709 in.) Z 2.45 mm (0.0965 in.)
M 1.85 mm (0.0728 in.) 1 2.50 mm (0.0984 in.)
N 1.90 mm (0.0748 in.) - -


HINT:

Select a thicker bearing shim to increase the preload, or a thinner bearing shim to decrease the preload.



f.

Remove the 17 bolts and manual transmission case sub-assembly.


g.

Remove the output shaft assembly from the front transaxle case.


h.

Remove the differential case from the front transaxle case.


i.

Replace the installed rear output shaft bearing shim with the one selected above.


Hide 33253H 7.INSTALL OUTER SHIFT LEVER OIL SEAL

a.
C200165
2.479,1.802 2.479,2.313 false 1.75,2.323 2.688,2.323 false 1.458,0.76 0.938,1.156 0.938,1.156 0.792,1.156 false 2.719,0.427 1.844,0.427 false 2.302,0.438 2.302,0.604 2.302,0.604 1.938,0.604 false 2.792,0.344 3.292,0.635 0.5,0.292 10 false SST 2.823,2.24 3.323,2.531 0.5,0.292 10 false SST 0.854,0.604 1.167,0.885 0.313,0.281 10 false *a 0.542,1.073 0.813,1.365 0.271,0.292 10 false *1
*1 Outer Shift Lever Oil Seal
*a Depth


Using SST and a hammer, tap in a new outer shift lever oil seal to the manual transmission case sub-assembly.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

Standard depth:

0.5 to 1.0 mm (0.0197 to 0.0393 in.)



b.

Coat the lip of the outer shift lever oil seal with MP grease.


Hide 8.INSTALL OUTER NO. 1 SHIFT LEVER

a.
C248157

Install the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever to the manual transmission case sub-assembly.


b.

Using a (5 mm) pin punch and hammer, tap in the inner shift lever slotted spring pin to the inner No. 1 shift lever.

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 9.INSTALL NO. 1 OIL RECEIVER PIPE

a.
C202193

Install the No. 1 oil receiver pipe to the manual transmission case sub-assembly.

HINT:

Make sure that the No. 1 oil receiver pipe fully contacts the manual transmission case sub-assembly.



Hide 31105C 10.INSTALL TRANSAXLE CASE STRAIGHT PIN

a.
C202190
2.156,2.656 2.75,2.656 false 2.823,2.573 3.208,2.854 0.385,0.281 10 false *a
*a 10.5 to 11.5 mm


Using a plastic-faced hammer, tap in 5 new transaxle case straight pins to the specified protrusion height.

Protrusion height:

10.5 to 11.5 mm (0.413 to 0.452 in.)



Hide 33101J 11.INSTALL BREATHER PLUG

a.
C200166
2.188,0.208 2.042,0.208 2.042,0.208 2.042,0.5 false 2.25,0.125 2.698,0.406 0.448,0.281 10 false SST

Using SST and a hammer, tap in the breather plug to the front transaxle case.

SST
09350-30020  (09350-07110)


Hide 31105D 12.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C200167
2.979,1.698 2.385,1.698 2.385,1.698 1.958,2.135 false 3.042,1.604 3.385,1.938 0.344,0.333 10 false SST 2.885,0.177 3.208,0.49 0.323,0.313 10 false *a
*a Depth


Using SST and a hammer, tap in a new front transaxle case oil seal to the front transaxle case.

SST
09612-22011  

Standard depth:

1.0 to 2.0 mm (0.0393 to 0.0787 in.)



b.

Coat the lip of the front transaxle case oil seal with MP grease.


Hide 33449B 13.INSTALL TRANSMISSION MAGNET

a.
C202185

Clean the transmission magnet and install it to the front transaxle case.


Hide 33137 14.INSTALL INPUT SHAFT COVER

a.
C202192
2.063,0.615 2.385,0.313 2.385,0.313 2.531,0.313 false 1.49,1.198 1.771,0.219 1.771,0.219 1.531,0.219 false 2.646,0.219 2.917,0.531 0.271,0.313 10 false *a 1.333,0.135 1.635,0.438 0.302,0.302 10 false *b
*a Input Shaft Cover Key
*b Manual Transmission Case Sub-assembly Groove


Install the input shaft cover to the manual transmission case sub-assembly.

NOTICE:

Insert the input shaft cover key into the manual transmission case sub-assembly groove.



Hide 33311K 15.INSTALL REAR INPUT SHAFT BEARING SHIM

a.

Install the rear input shaft bearing shim onto the manual transmission case sub-assembly.

NOTICE:

Apply MP grease to the shim to prevent it from falling off the case during assembly.



b.
C287178
1.021,0.688 1.385,0.688 false 1.302,2.333 1.76,2.333 false 1.115,3.958 1.115,3.625 1.115,3.625 0.948,3.625 false 0.76,0.615 1.094,0.927 0.333,0.313 10 false *1 2.802,0.615 3.156,0.938 0.354,0.323 10 false *a 2.781,2.219 3.156,2.531 0.375,0.313 10 false *b 1.073,2.271 1.375,2.531 0.302,0.26 10 false *2 2.958,3.917 3.271,4.198 0.313,0.281 10 false *c 0.729,3.552 1.073,3.854 0.344,0.302 10 false *3
*1 Manual Transmission Case
*2 Input Shaft Assembly
*3 Front Transaxle Case
*a Dimension A
*b Dimension C
*c Dimension B


Measure the distance between the end of the manual transmission case and rear input shaft bearing shim (Dimension A).


c.

Measure the distance between the end of the front transaxle case and installation surface of the front input shaft bearing (Dimension B).


d.

Measure the distance between both input shaft bearing outer races (Dimension C).

NOTICE:

Measure Dimension C when both bearings have no clearance.



e.

Calculate the rear input shaft bearing shim clearance using the following formula.

Formula:

(Dimension A + Dimension B) - Dimension C - Rear input shaft bearing shim thickness = Between 0 mm and 0.1 mm (0.00394 in.)


If the clearance is not as specified, replace the rear input shaft bearing shim with one of a different thickness. Use the table below to select a rear input shaft bearing shim which will ensure that the clearance is within the specification.

Standard Rear Input Shaft Bearing Shim Thickness:
Mark Specified Condition Mark Specified Condition
A 1.15 mm (0.0453) H 1.50 mm (0.0591)
B 1.20 mm (0.0472) J 1.55 mm (0.0610)
C 1.25 mm (0.0492) K 1.60 mm (0.0630)
D 1.30 mm (0.0512) L 1.65 mm (0.0650)
E 1.35 mm (0.0531) M 1.70 mm (0.0669)
F 1.40 mm (0.0551) N 1.75 mm (0.0689)
G 1.45 mm (0.0571) P 1.80 mm (0.0709)



f.

Coat the selected rear input shaft bearing shim with MP grease, and then replace the installed rear input shaft bearing shim with the one selected above.

NOTICE:

Do not apply MP grease to the oil grooves.



Hide 16.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C202182

Coat the differential case with gear oil and install it to the front transaxle case.


Hide 17.INSTALL INPUT SHAFT ASSEMBLY

a.

Apply gear oil to all sliding and rotating parts.


b.
C200169
1.813,2.729 2.354,2.729 false 2.073,1.177 2.073,0.75 2.073,0.75 2.302,0.75 false 2.375,0.677 2.656,0.948 0.281,0.271 10 false *1 2.438,2.656 2.771,2.906 0.333,0.25 10 false *2
*1 No. 1 Gear Shift Fork Shaft Assembly
*2 Output Shaft Assembly


Coat the No. 1 gear shift fork shaft assembly with gear oil and install it onto the output shaft assembly.


c.
C200170
2.323,0.75 2.135,0.75 2.135,0.75 2.135,1.156 false 2.698,3.208 2.438,3.208 2.438,3.208 2.438,3.573 false 2.417,0.677 2.688,0.969 0.271,0.292 10 false *1 2.781,3.135 3.083,3.417 0.302,0.281 10 false *2
*1 No. 2 Gear Shift Fork Shaft Assembly
*2 Input Shaft Assembly


Coat the No. 2 gear shift fork shaft assembly with gear oil and install it onto the input shaft assembly.


d.

Temporarily install the output shaft assembly with No. 1 gear shift fork shaft assembly to the input shaft assembly, and tie them with a rope or string.


e.
C202181

Install the input shaft assembly, output shaft assembly and 2 gear shift fork shaft assemblies to the front transaxle case.


Hide 33257C 18.INSTALL OUTER SELECT LEVER OIL SEAL

a.
C223810
1.083,1.479 0.99,1.479 0.99,1.479 0.865,1.313 false 0.375,1.917 0.375,1.156 false 0.375,1.458 0.625,1.458 0.625,1.458 0.625,1.219 false 2.156,1.365 2.781,1.365 2.781,1.365 2.781,3.042 true 2.198,2.094 2.781,2.094 true 1.177,0.208 1.49,0.469 0.313,0.26 10 false *a 1.156,1.417 1.438,1.688 0.281,0.271 10 false *1 0.271,1.969 0.74,2.333 0.469,0.365 10 false SST 2.646,3.104 3.021,3.333 0.375,0.229 10 true SST
*1 Outer Select Lever Oil Seal
*a Depth


Using SST and a hammer, tap in a new outer select lever oil seal to the front transaxle case.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)

Standard depth:

0.5 to 1.0 mm (0.0197 to 0.0393 in.)



b.

Coat the lip of the outer select lever oil seal with MP grease.


Hide 19.INSTALL OUTER SELECT LEVER

a.
C248155
2.802,0.281 2.656,0.281 2.656,0.281 2.583,0.542 false 2.865,0.208 3.167,0.448 0.302,0.24 10 false *a
*a Mark


Install the outer select lever and inner select lever to the front transaxle case.

HINT:

Install the inner select lever with its mark positioned outside of the front transaxle case.



b.
C202180

Coat the threads of the inner select lever set bolt with adhesive and install it.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 20.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C200174

Install the shift interlock plate and shift and select lever shaft assembly to the front transaxle case, and then turn them counterclockwise.

HINT:

When installing the shift interlock plate, make sure to engage it with the inner select lever.



Hide 33240 21.INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

a.
C202179

Coat the threads of the 2 bolts with adhesive and install the 2 bolts using a hexagon socket wrench (6 mm).

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
17 N*m (173 kgf*cm, 12 ft.*lbf)


Hide 33211 22.INSTALL REVERSE SHIFT FORK

a.
C200913

Using a (5 mm) pin punch and hammer, install the reverse shift fork and reverse shift fork slotted spring pin onto the No. 4 gear shift fork shaft.

Standard driven in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Confirm the installation direction.



b.
C202834

Coat the No. 4 gear shift fork shaft with gear oil and install it onto the front transaxle case.


Hide 33402 23.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C287179
0.729,0.979 1.188,0.521 1.188,0.521 1.573,0.521 false 0.969,1.25 1.844,1.25 false 1.656,0.438 2,0.74 0.344,0.302 10 false *a 1.917,1.167 2.292,1.469 0.375,0.302 10 false *b
*a Case Hole
*b I-groove mark of the reverse idler gear shaft


Coat the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft with gear oil, and install them as shown in the illustration.

NOTICE:

Using the bolt hole of the case for reference, align the I-groove mark of the reverse idler gear shaft within the range shown (approximately 20°).


HINT:

Raise the edge of the reverse shift arm bracket assembly and install it to the reverse shift fork shaft assembly.



Hide 33101 24.INSTALL MANUAL TRANSMISSION CASE SUB-ASSEMBLY

a.
C202201

Apply seal packing to the manual transmission case sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Seal packing diameter:

1.2 mm (0.0472 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Assemble the parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.




b.
C248535

Push the outer No. 1 shift lever and install the manual transmission case sub-assembly.

HINT:

Pushing the outer No. 1 shift lever allows the manual transmission case sub-assembly to be installed.



c.
C248722

Turn the outer No. 1 shift lever counterclockwise and then pull it.


d.
C203963

Install the manual transmission case sub-assembly with the 17 bolts.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33253F 25.INSTALL OUTER SHIFT LEVER E RING

a.
C248151

Install the outer shift lever E ring to the outer No. 1 shift lever.


Hide 33111Q 26.INSTALL TRANSMISSION CASE OIL SEAL

a.
C199963
1.479,1.292 0.521,0.594 0.521,0.594 1.323,1.417 false 2.563,2.74 2.219,2.875 2.219,2.875 2.354,2.604 false 0.219,0.5 0.667,0.75 0.448,0.25 10 false SST 1.927,2.854 2.333,3.094 0.406,0.24 10 false SST

Using SST and a hammer, tap in a new transmission case oil seal to the manual transmission case sub-assembly.

SST
09608-32010  
09950-70010  (09951-07100)

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not damage the oil seal lip.



b.

Coat the lip of the transmission case oil seal with MP grease.


Hide 31105H 27.INSTALL TRANSAXLE CASE OIL SEAL

a.
C199964
1.656,1.198 2.698,0.969 2.698,0.969 1.813,1.375 true 1.375,2.635 1.635,2.885 1.635,2.885 1.208,2.698 false 2.771,0.885 3.24,1.156 0.469,0.271 10 false SST 1.688,2.854 2.104,3.125 0.417,0.271 10 false SST

Using SST and a hammer, tap in a new transaxle case oil seal to the front transaxle case.

SST
09710-30050  
09950-70010  (09951-07100)

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not damage the oil seal lip.



b.

Coat the lip of the transaxle case oil seal with MP grease.


Hide 33275C 28.INSTALL SHIFT DETENT BALL

a.

Install the 2 shift detent balls and 2 shift detent ball compression springs into the manual transmission case sub-assembly.

NOTICE:

Be careful not to drop the balls into the manual transmission case sub-assembly.



b.
C199073

Coat the threads of the 2 shift detent ball plugs with adhesive and install them using a (6 mm) hexagon socket wrench.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


c.
C199072

Install the shift detent ball and compression spring into the manual transmission case sub-assembly.

NOTICE:

Be careful not to drop the ball into the manual transmission case sub-assembly.



d.

Coat the threads of the shift detent ball plug with adhesive and install it using a (6 mm) hexagon socket wrench.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 33292A 29.INSTALL LOCK BALL PIN

a.

Install the lock ball pin and shift and select lever shaft compression spring into the manual transmission case sub-assembly.

NOTICE:

Be careful not to drop the lock ball pin into the manual transmission case sub-assembly.



b.
C248150

Coat the threads of the shift and select lever shaft straight screw with head plug with adhesive and install it using a (10 mm) hexagon socket wrench.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


c.

Install the lock ball pin and shift and select lever shaft compression spring into the manual transmission case sub-assembly.

NOTICE:

Be careful not to drop the lock ball pin into the manual transmission case sub-assembly.



d.
C199069

Coat the threads of the shift and select lever shaft straight screw with head plug with adhesive and install it using a (10 mm) hexagon socket wrench.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 33451H 30.INSTALL REVERSE IDLER GEAR SHAFT BOLT

a.
C199070

Coat the threads of the reverse idler gear shaft bolt with sealant and install it onto the manual transmission case sub-assembly with a new gasket.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 31.INSTALL RELEASE CYLINDER BLEEDER PLUG

a.

Install the release cylinder bleeder plug to the clutch release bleeder.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 31478 32.INSTALL RELEASE CYLINDER BLEEDER PLUG CAP

a.

Install the release cylinder bleeder plug cap to the release cylinder bleeder plug.


Hide 31400 33.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

Hide 31407B 34.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 35.INSPECT CLUTCH PIPE LINE

Hide 31407B 36.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 37.INSTALL CONTROL CABLE BRACKET

a.
C248148

Install the control cable bracket to the manual transmission case sub-assembly with the 3 bolts.

Torque:
17 N*m (173 kgf*cm, 12 ft.*lbf)


Hide 84210 38.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
C199065

Using a (27 mm) deep socket wrench, install a new gasket and the back-up light switch assembly to the manual transmission case sub-assembly.

Torque:
40 N*m (410 kgf*cm, 30 ft.*lbf)


Hide 33111C 39.INSTALL TRANSMISSION CASE PLUG

a.
C205244

Install the transmission case plug onto the manual transmission case sub-assembly with a new gasket.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 40.INSTALL MANUAL TRANSMISSION DRAIN PLUG

a.
C199063

Install a new gasket and the manual transmission drain plug to the front transaxle case.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 41.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
C199064

Install a new gasket and the manual transmission filler plug to the manual transmission case sub-assembly.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)