Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › 2011.10–2016.05
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074033 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  INSTALLATION  


PROCEDURE

Hide 44510 1.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C236074N01
1.521,1.75 1.906,1.99 0.385,0.24 10 1 2.344,1.708 2.792,2.01 0.448,0.302 10 2 2.635,0.542 3.021,0.865 0.385,0.323 10 3

Install the brake actuator assembly to the brake actuator bracket assembly.

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.




b.

Tighten the 3 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Tighten the 3 nuts in the order shown in the illustration.



Hide 2.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C239183N01
2.802,0.281 2.979,0.448 0.177,0.167 10 true 1 2.417,1.26 2.844,1.583 0.427,0.323 10 false 2 0.281,1.563 1,1.781 0.719,0.219 10 false 3

Install the brake actuator with bracket to the vehicle body with the 3 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not damage the brake lines, suction hose sub-assembly or wire harness.

·

Tighten the 3 bolts in the order shown in the illustration.




b.
C239182C01
1.885,0.49 2.51,0.219 true 1.656,0.615 0.865,0.177 true 1.51,0.771 0.823,0.552 true 1.375,0.927 0.573,1.083 true 1.792,1.208 1.906,1.792 true 2.042,0.948 2.292,1.542 true 1.833,1.771 2.24,2 0.406,0.229 10 false *a 2.24,1.563 2.844,1.854 0.604,0.292 10 false *b 2.531,0.115 2.99,0.396 0.458,0.281 10 false *c 0.688,0.073 1.083,0.344 0.396,0.271 10 false *d 0.646,0.458 1.083,0.771 0.438,0.313 10 false *e 0.438,1 0.875,1.292 0.438,0.292 10 false *f
*a From 1st Chamber of Master Cylinder Sub-assembly
*b From 2nd Chamber of Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.


c.

Using a union nut wrench, fully tighten each brake line.

Torque:
flare nut *a, *b (w/o VSC) : 15 N*m (155 kgf*cm, 11 ft.*lbf)
flare nut *a, *b (w/ VSC) : 20 N*m (199 kgf*cm, 14 ft.*lbf)
flare nut *c, *d, *e, *f : 15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



d.
C239181N03
1.646,0.594 0.875,0.313 true 2.125,3.896 2.323,4.104 2.323,4.104 2.573,4.104 true 0.76,0.24 1.563,0.625 0.802,0.385 9 false b 2.604,4.031 3.021,4.323 0.417,0.292 9 false a

Connect the connector to the brake actuator assembly and disengage the claw (b).


e.

Put the lever down and engage the claw (a) to engage the connector lock.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter.




Hide 3.INSTALL SUCTION PIPE CLAMP

a.

Engage the suction pipe clamp to install it to the brake actuator bracket assembly.


Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.BLEED BRAKE SYSTEM

Hide 6.INSPECT BRAKE ACTUATOR USING INTELLIGENT TESTER