Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2015.04
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using the Intelligent Tester)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Read the DTCs following the prompts on the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105



b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Operate the intelligent tester to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / DTC / Clear.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105



DTC CHECK/CLEAR (When not Using the Intelligent Tester)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.
C166029C18
1.583,0.906 1.583,0.5 false 1.771,1.885 1.771,1.479 false 1.677,1.896 1.917,2.073 0.24,0.177 10 TC 1.469,0.302 1.771,0.479 0.302,0.177 10 CG 0.167,0.115 0.385,0.292 0.219,0.177 10 *a
*a Front view of DLC3


Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.

Observe the blinking pattern of the ABS warning and slip indicator lights in order to identify the DTC.

HINT:

If no code appears, inspect the TC and CG terminal circuit, and ABS warning and slip indicator light circuits.


Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)


v.

Count the number of blinks of the ABS warning and slip indicator lights.

HINT:
·

How to read DTCs:

Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.

·

If one code is detected:

The light repeats the same code after a pause of 4 seconds.

·

If multiple codes are detected:

The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.




vi.

Check the details of the DTCs.

ABS DTC
ABS Warning Light Display Tester Display
11 C146E
13 C146C
21 C1468
22 C1469
23 C146A
24 C146B
25 C1225
26 C1226
27 C1227
28 C1228
31 C1464
32 C1465
33 C1466
34 C1467
35 C1330
36 C1331
37 C1237
38 C1332
39 C1333
41 C1241
C1417
46 C1246
49 C1249
C1425
C1426
51 C1428
62 C1300
67 C1429
C1430
C1431
94 U0073

VSC DTC
Slip Indicator Light Display Tester Display
28 C1472
31 C1432
C1433
C1434
C1439
C1445
32 C1419
C1420
34 C1234
C1435
C1436
43*1 -
44 C1224
51 C1201
62 U0123
63 U0126
65 U0100
6A*2 C1381
88 C1288

*1: This DTC is output when the VSC system detects a malfunction in the ABS.

*2: The light blinks 6 times, turns off for 1.5 seconds, and then blinks 10 times.


vii.

After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.



b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.
C166029C18
1.583,0.906 1.583,0.5 false 1.771,1.885 1.771,1.479 false 1.677,1.896 1.917,2.073 0.24,0.177 10 TC 1.469,0.302 1.771,0.479 0.302,0.177 10 CG 0.167,0.115 0.385,0.292 0.219,0.177 10 *a
*a Front view of DLC3


Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


v.

Check that the warning light indicates a normal system code.


vi.

Remove SST from the terminals of the DLC3.

HINT:

The DTCs cannot be cleared by disconnecting the battery terminal or the ECU-IG1 NO. 1 fuse.





END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning and slip indicator lights go off within approximately 3 seconds after turning the ignition switch to ON.