Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
42431
1.INSTALL REAR DISC
| *a | Matchmark |
Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.
When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.
42491
2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
Install the parking brake shoe adjusting hole plug.
47722A
3.INSTALL DISC BRAKE CYLINDER MOUNTING
for PBR Made:
Install the disc brake cylinder mounting with the 2 bolts.
for ADVICS Made:
Install the disc brake cylinder mounting with the 2 bolts.
47775D
4.INSTALL REAR DISC BRAKE BUSHING DUST BOOT
for PBR Made:
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the seal surfaces of 2 new rear disc brake bushing dust boots.
Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.
Apply a light layer of lithium soap base glycol grease to the sliding part and the seal surface of the rear disc brake cylinder slide pin.
Install the rear disc brake bushing dust boot to each rear disc brake cylinder slide pin.
for ADVICS Made:
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.
Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.
Install the 2 rear disc brake bushing dust boots to the disc brake cylinder mounting.
47715C
5.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN
for PBR Made:
Install the 2 rear disc brake cylinder slide pins to the disc brake cylinder mounting.
Install the 2 rear disc brake bushing dust boots to the groove of the rear brake cylinder mounting.
6.INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSHING
for ADVICS Made:
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the contact surface of the rear disc brake cylinder slide pin.
Install a new rear disc brake cylinder slide bushing to the rear disc brake cylinder slide pin.
47814
7.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)
for ADVICS Made:
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the rear disc brake cylinder slide pin.
Install the rear disc brake cylinder slide pin to the disc brake cylinder mounting.
Push the rear disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.
47814
8.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)
for ADVICS Made:
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the rear disc brake cylinder slide pin.
Install the rear disc brake cylinder slide pin to the disc brake cylinder mounting.
Push the rear disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.
47716A
9.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE
for ADVICS Made:
| *1 | Rear Disc Brake Pad Support Plate |
| *2 | Disc Brake Cylinder Mounting |
Install the 2 rear disc brake pad support plates to the disc brake cylinder mounting.
Firmly push to install the rear disc brake pad support plate and disc brake cylinder mounting against each other so that there is no clearance between the surfaces A and a, and B and b.
04946
10.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT
for ADVICS Made:
Install the pad wear indicator plate to each rear disc brake pad.
Install each pad wear indicator plate in the correct position and direction.
|
Disc Brake Grease |
Apply disc brake grease to the inside of the rear disc brake anti-squeal shims.
Install the rear disc brake anti-squeal shim to each rear disc brake pad with pad wear indicator plate.
Disc brake grease may seep out slightly from the areas where the rear disc brake anti-squeal shims are installed.
Make sure that disc brake grease is not applied onto the lining surface.
04466
11.INSTALL REAR DISC BRAKE PAD
for PBR Made:
| *A | Outer Side |
| *B | Inner Side |
| *1 | Pad Wear Indicator |
Install the 2 rear disc brake pads to the disc brake cylinder mounting.
There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.
for ADVICS Made:
Install the 2 rear disc brake pads with rear disc brake anti-squeal shim kit to the disc brake cylinder mounting.
There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.
47850
12.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY
for PBR Made:
| *a | Hold |
| *b | Turn |
Hold the rear disc brake cylinder slide pin, and install the rear disc brake cylinder assembly to the disc brake cylinder mounting with the 2 bolts.
Make sure that the rear brake pad springs do not get caught at the point on the rear disc brake cylinder assembly shown in the illustration.
for ADVICS Made:
| *a | Hold |
| *b | Turn |
Hold the rear disc brake cylinder slide pin, and install the rear disc brake cylinder assembly to the disc brake cylinder mounting with the 2 bolts.
Make sure that the rear brake pad springs do not get caught at the point on the rear disc brake cylinder assembly shown in the illustration.
47319F
13.CONNECT REAR FLEXIBLE HOSE
for PBR Made:
| *a | Lock Hole |
Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and 2 new gaskets.
Install the flexible hose lock securely into the lock hole in the disc brake cylinder.
for ADVICS Made:
| *a | Lock Hole |
Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.
Install the flexible hose lock securely into the lock hole in the disc brake cylinder.
14.BLEED BRAKE LINE
15.ADJUST PARKING BRAKE
16.INSTALL REAR WHEEL