Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074080 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E232803E02
2.781,0.561 2.875,0.712 0.095,0.151 10 5 2.733,0.747 2.922,0.898 0.19,0.151 10 z3 3.795,0.561 3.968,0.712 0.173,0.151 10 13 3.79,0.747 4.002,0.898 0.213,0.151 10 I28 3.2,0.661 3.494,0.812 0.295,0.151 10 IL+2 2.781,1.309 2.875,1.46 0.095,0.151 10 3 2.733,1.496 2.922,1.647 0.19,0.151 10 z3 3.795,1.309 3.968,1.46 0.173,0.151 10 11 3.79,1.496 4.002,1.647 0.213,0.151 10 I28 3.214,1.409 3.473,1.56 0.259,0.151 10 -DP 2.91,1.85 3.81,2.195 0.9,0.345 10 Spiral Cable Sub-assembly 0.882,1.085 1.082,1.236 0.2,0.151 10 LH 0.882,1.838 1.232,1.989 0.35,0.151 10 RH 0.404,2.486 2.326,2.637 1.922,0.151 10 Steering Pad Switch Assembly 0.382,3.479 1.156,3.63 0.774,0.151 10 from Battery 2.572,4.154 2.884,4.305 0.313,0.151 10 TAIL 3.441,3.628 3.919,3.779 0.478,0.151 10 PANEL 4.461,3.872 5.622,4.023 1.162,0.151 10 to Main Body ECU 5.877,4.644 6.853,4.962 0.976,0.318 10 Radio Receiver Assembly 6.02,0.748 6.315,0.899 0.295,0.151 10 ILL+ 5.767,0.657 5.939,0.808 0.172,0.151 10 10 5.877,4.476 6.251,4.627 0.374,0.151 10 I148 4.599,4.184 5.839,4.507 1.24,0.323 10 (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (w/ VSC).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PRECAUTION


·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (w/o VSC).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>PRECAUTION


·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio receiver assembly. B
No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I28-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.


b.

Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

E233724C02
2.708,0.802 3.083,1.031 0.375,0.229 3.51,0.854 2.74,0.313 false 3.719,0.875 4.448,1.042 false 0.198,0.219 1.167,1.344 0.969,1.125 10 false *a 2.833,0.833 3.208,1.135 0.375,0.302 10 false z3 2.469,0.229 2.896,0.563 0.427,0.333 10 false -DP 4.49,0.99 4.958,1.375 0.469,0.385 10 false IL+2
*a Component without harness connected
(Steering Pad Switch Assembly)
- -



c.

Check if the illumination for the steering pad switch assembly comes on.

OK:

Illumination for the steering pad switch assembly comes on.



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Disconnect the steering pad switch assembly and spiral cable sub-assembly connectors.


b.
E263757C04
1.344,0.677 1.677,0.906 0.333,0.229 0.427,3.865 0.76,4.094 0.333,0.229 1.781,1.021 2,0.583 false 2.271,0.594 2.542,0.969 false 1.042,4.26 1.302,3.76 false 1.792,4.24 1.521,3.76 false 0.24,0.188 0.625,0.479 0.385,0.292 10 *a 1.177,0.25 1.563,0.542 0.385,0.292 10 *b 0.354,3.563 0.74,3.854 0.385,0.292 10 *c 1.552,1.052 2.167,1.25 0.615,0.198 10 IL+2 2.5,1.021 2.885,1.26 0.385,0.24 10 -DP 1.438,0.708 1.75,0.906 0.313,0.198 10 z3 0.885,4.302 1.271,4.542 0.385,0.24 10 -DP 1.646,4.26 2.26,4.458 0.615,0.198 10 IL+2 0.51,3.896 0.969,4.094 0.458,0.198 10 I28
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z3-3 (-DP) - I28-11 (-DP) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Always Below 3 Ω
z3-3 (-DP) - I28-11 (-DP) Always Below 3 Ω


NOTICE:
·

Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



HINT:



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I148-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR