Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2011.10–2016.05
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074150 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 2. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 84306 3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

a.
B474842C02
0.677,0.542 0.677,0.719 0.677,0.719 0.333,0.719 true 0.708,1.531 0.302,1.531 true 0.073,0.125 0.385,0.281 0.313,0.156 10 false *A 0.083,1.125 0.396,1.281 0.313,0.156 10 false *B 0.177,0.615 0.385,0.792 0.208,0.177 10 false *a 0.135,1.448 0.448,1.604 0.313,0.156 10 false *b
*A Flat Cable Type
*B Colored Roller Type
*a Flat Cable
*b Colored Roller


Check the colored roller or flat cable shown in the illustration.

If the colored roller or flat cable shown in the illustration cannot be confirmed, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly or spiral cable with sensor sub-assembly with a new one.


Hide 45287 4.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

Hide 84306 6.REMOVE SPIRAL CABLE SUB-ASSEMBLY (w/o VSC)

NOTICE:
·

Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch to ON.

·

Do not rotate the spiral cable sub-assembly without the steering wheel with the battery connected and the ignition switch to ON.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.


c.

Check that the front wheels are facing straight ahead.


d.
B279735C02
1.5,1.946 1.677,2.13 0.177,0.184 10 *a 0.915,2.328 1.23,2.013 1.23,2.013 1.46,2.013 false
*a Slider


Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.

Disconnect the other connector from the spiral cable sub-assembly.


f.
B279736

Disengage the 3 claws to remove the spiral cable sub-assembly.


Hide 7.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/ VSC)

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch to ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the battery connected and the ignition switch to ON.

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.


c.

Check that the front wheels are facing straight ahead.


d.
B279735C02
1.5,1.946 1.677,2.13 0.177,0.184 10 *a 0.915,2.328 1.23,2.013 1.23,2.013 1.46,2.013 false
*a Slider


Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.

Disconnect the other connector from the spiral cable with sensor sub-assembly.


f.
B279736

Disengage the 3 claws to remove the spiral cable with sensor sub-assembly.


Hide 84306 8.REMOVE SPIRAL CABLE SUB-ASSEMBLY (w/ VSC)

NOTICE:
·

Remove the spiral cable sub-assembly from the steering sensor only when replacing it or the steering sensor.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in a misaligned center position of the steering sensor. Therefore, make sure to use the lock pin provided with a new spiral cable sub-assembly or steering sensor when removing the steering sensor from the spiral cable sub-assembly.

·


a.
C238437

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable sub-assembly.

·

Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.




b.
B279788C02
0.938,0.74 1.844,0.365 false 0.979,1.281 1.823,1.813 false 1.854,0.26 2.083,0.469 0.229,0.208 10 false *1 1.854,1.75 2.063,1.948 0.208,0.198 10 false *1
*1 Guide


Disengage the 6 claws and 2 pins to remove the spiral cable sub-assembly from the steering sensor.

NOTICE:
·

Do not damage the claw of the steering sensor.

·

Do not damage the guide.