Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074080 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the combination meter assembly.


for "Bluetooth":

Speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E230186E01
0.46,1.382 1.583,1.534 1.123,0.151 10 Skid Control ECU 0.867,0.583 1.158,0.734 0.292,0.151 10 SP1 0.153,1.382 0.472,1.564 0.319,0.181 10 A49 1.207,0.583 1.394,0.731 0.187,0.148 10 2 0.119,2.737 3.204,2.901 3.085,0.164 10 Certification ECU (Smart Key ECU Assembly)*5 0.119,2.584 0.41,2.748 0.291,0.164 10 I78 0.063,7.472 0.328,7.636 0.266,0.164 10 I72 0.374,7.472 2.686,7.79 2.313,0.319 10 Windshield Wiper Relay Assembly*4 1.687,7.081 2.101,7.236 0.414,0.155 10 SPD 1.637,2.338 2.038,2.492 0.401,0.155 10 SPD 2.108,2.334 2.288,2.493 0.18,0.159 10 27 2.931,2.334 3.11,2.493 0.18,0.159 10 21 3.941,2.334 4.121,2.493 0.18,0.159 10 18 2.931,3.747 3.11,3.906 0.18,0.159 10 19 3.941,3.747 4.121,3.906 0.18,0.159 10 17 2.087,7.081 2.271,7.24 0.184,0.159 10 24 3.953,7.102 4.136,7.261 0.184,0.159 10 16 2.934,7.102 3.118,7.261 0.184,0.159 10 20 5.345,7.103 5.549,7.265 0.204,0.162 10 57 5.296,5.108 5.513,5.27 0.217,0.162 10 17 5.419,0.564 5.723,0.714 0.304,0.15 10 8 5.419,2.348 5.695,2.498 0.276,0.15 10 9 5.589,0.662 5.788,0.812 0.199,0.15 10 SI 5.583,2.446 5.784,2.597 0.201,0.151 10 +S 5.009,2.779 5.341,2.925 0.332,0.146 10 I18 5.285,2.779 7.12,2.972 1.836,0.193 10 Combination Meter Assembly 5.781,7.479 6.058,7.632 0.277,0.153 10 A25 6.102,7.479 6.513,7.655 0.411,0.176 10 ECM 4.409,5.633 6.988,5.999 2.58,0.366 10 Navigation ECU Sub-assembly*2 or Radio and Display Receiver Assembly*3 2.353,8.235 4.748,8.398 2.395,0.163 10 *5: w/ Smart Entry and Start System 0.317,8.235 1.993,8.395 1.676,0.16 10 *4: w/ Auto Wiper System 4.808,7.912 6.716,8.094 1.907,0.182 10 *3: for Radio and Display Type 5.662,7.092 5.991,7.238 0.329,0.145 10 SPD 5.588,5.201 5.917,5.347 0.329,0.145 10 SPD 5.588,3.771 5.917,3.917 0.329,0.145 10 SPD 5.256,5.286 5.575,5.432 0.319,0.146 10 I155 5.307,5.473 5.497,5.619 0.19,0.146 10 *3 4.939,5.108 5.155,5.27 0.217,0.162 10 17 4.927,5.286 5.202,5.432 0.276,0.146 10 I67 4.944,5.473 5.129,5.619 0.185,0.146 10 *2 2.111,3.76 2.423,3.922 0.312,0.162 10 11 0.595,4.162 0.87,4.316 0.275,0.153 10 I69 5.326,3.771 5.638,3.933 0.312,0.162 10 17 4.99,4.144 5.53,4.304 0.54,0.16 10 I150 0.903,4.162 2.405,4.526 1.501,0.364 10 Stereo Component Amplifier Assembly*2 5.328,4.144 7.082,4.321 1.754,0.176 10 Radio Receiver Assembly*1 1.712,3.773 2.04,3.918 0.329,0.145 10 SPD 2.438,7.912 4.475,8.094 2.037,0.182 10 *2: for Navigation Receiver Type 0.317,7.912 2.107,8.082 1.79,0.169 10 *1: for Radio Receiver Type 3.094,7.472 4.314,7.634 1.22,0.162 10 Junction Connector 2.782,7.472 3.183,7.636 0.401,0.164 10 I124

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Check the output waveform.

E265532C01
1.781,0.302 2.156,0.563 0.375,0.26 1.49,1.979 1.771,1.302 false 1.885,0.354 2.344,0.552 0.458,0.198 10 l18 0.271,0.198 0.583,0.396 0.313,0.198 10 *a 6.083,1.458 6.542,1.656 0.458,0.198 10 GND 1.396,2.01 1.844,2.292 0.448,0.281 10 +S 4.615,1.625 5.073,1.823 0.458,0.198 10 (A)
*a Component with harness connected
(Combination Meter Assembly)
- -


i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I18-9 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-9 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the radio receiver assembly and combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-17 (SPD) - I18-9 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the radio receiver assembly connector and junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-17 (SPD) - I124-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)