Using this circuit, the radio receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly sends microphone signals to the radio receiver assembly.
Disconnect the radio receiver assembly connector.
Disconnect the roof console box assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I150-6 (SNS2) - S7-15 (SNS2) | Always | Below 1 Ω |
| I150-4 (MACC) - S7-14 (MACC) | Always | Below 1 Ω |
| I150-5 (MIN+) - S7-13 (MCO+) | Always | Below 1 Ω |
| I150-19 (MIN-) - S7-12 (MCO-) | Always | Below 1 Ω |
| I150-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| I150-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| I150-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| I150-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| I150-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the radio receiver assembly connector.
Reconnect the roof console box assembly (telephone microphone assembly) connector.
| *a | Component with harness connected
(Radio Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I150-4 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I150-18 (SGND) - Body ground | Always | Below 1 Ω |
| I150-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the roof console box assembly (telephone microphone assembly) connector.
| *a | Component without harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S7-12 (MCO-) - S7-15 (SNS2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the radio receiver assembly connector.
Reconnect the roof console box assembly (telephone microphone assembly) connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly)) |
Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the roof console box assembly (telephone microphone assembly) connector.
Check the waveform of the telephone microphone assembly using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the roof console box assembly is output | A |
| A waveform synchronized with the voice input to the roof console box assembly is not output | B |
A
B
Replace the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
Check if the same malfunction recurs.
| Result | Proceed to |
|---|---|
| Malfunction does not recur (returns to normal) | A |
| Malfunction recurs | B |
A
B