Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074080 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E238680E01
0.661,1.089 1.128,1.31 0.466,0.221 10 UDO- 0.801,0.468 1.055,0.689 0.253,0.221 10 UPI 0.675,2.177 1.094,2.398 0.419,0.221 10 UJSG 0.647,1.64 1.066,1.861 0.419,0.221 10 UDO+ 0.661,2.778 1.08,2.999 0.419,0.221 10 UJSS 6.153,1.089 6.62,1.31 0.466,0.221 10 US1- 6.153,0.468 6.555,0.689 0.402,0.221 10 USV1 6.153,2.177 6.572,2.398 0.419,0.221 10 UGD1 6.153,1.64 6.572,1.861 0.419,0.221 10 US1+ 6.153,2.778 6.572,2.999 0.419,0.221 10 USG1 1.16,0.369 1.293,0.59 0.133,0.221 10 1 1.16,1.001 1.293,1.222 0.133,0.221 10 2 1.16,1.538 1.293,1.759 0.133,0.221 10 3 1.16,2.08 1.293,2.301 0.133,0.221 10 4 1.16,2.682 1.293,2.903 0.133,0.221 10 5 0.152,3.143 0.571,3.305 0.419,0.163 10 I146 0.152,3.289 2.687,3.481 2.535,0.192 10 No. 1 Stereo Jack Adapter Assembly 3.318,2.904 4.006,3.141 0.688,0.237 10 (Shielded) 5.937,0.369 6.071,0.59 0.133,0.221 10 1 5.937,0.996 6.071,1.217 0.133,0.221 10 2 5.937,1.538 6.071,1.759 0.133,0.221 10 3 5.937,2.08 6.071,2.301 0.133,0.221 10 4 5.937,2.682 6.071,2.903 0.133,0.221 10 5 5.462,3.143 5.826,3.305 0.364,0.163 10 I151 5.462,3.289 7.092,3.463 1.63,0.173 10 Radio Receiver Assembly

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while before play begins.

·

When using a USB device, files that are copy protected or encrypted due to copyright reasons cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION


Result:
Result Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B




A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the radio receiver assembly and No. 1 stereo jack adapter assembly connectors.


b.
E211808C04
1.375,0.26 1.906,0.552 0.531,0.292 1.375,2.76 1.906,3.052 0.531,0.292 1.885,1.469 2.271,1.469 false 2.26,1.792 1.75,1.5 false 1.542,1.5 1.01,1.823 false 2.229,1.99 1.677,1.604 false 0.927,1.479 1.385,1.479 false 1.5,3.927 1.031,3.646 false 1.49,4.115 1.021,4.115 false 1.76,3.938 2.375,3.729 false 1.781,4.094 2.313,4.094 false 1.708,4.281 2.292,4.427 false 1.49,0.323 1.844,0.469 0.354,0.146 10 I146 2.313,1.406 2.854,1.583 0.542,0.177 10 UJSG 0.646,1.396 0.938,1.573 0.292,0.177 10 UPI 0.135,0.125 0.406,0.302 0.271,0.177 10 *a 0.115,2.625 0.302,2.802 0.188,0.177 10 *b 2.292,1.708 2.75,1.885 0.458,0.177 10 UDO+ 0.604,1.781 1,1.958 0.396,0.177 10 UDO- 2.26,1.948 2.656,2.125 0.396,0.177 10 UJSS 0.594,3.51 1.01,3.688 0.417,0.177 10 UGD1 2.417,3.635 2.833,3.813 0.417,0.177 10 USV1 2.344,4.365 2.76,4.542 0.417,0.177 10 USG1 0.604,4.031 1.021,4.208 0.417,0.177 10 US1+ 2.333,4.021 2.75,4.198 0.417,0.177 10 US1- 1.49,2.823 1.844,2.969 0.354,0.146 10 I151
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
*b Front view of wire harness connector
(to Radio Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I151-1 (USV1) Always Below 1 Ω
I146-2 (UDO-) - I151-2 (US1-) Always Below 1 Ω
I146-3 (UDO+) - I151-3 (US1+) Always Below 1 Ω
I146-4 (UJSG) - I151-4 (UGD1) Always Below 1 Ω
I146-5 (UJSS) - I151-5 (USG1) Always Below 1 Ω
I146-1 (UPI) - Body ground Always 10 kΩ or higher
I146-2 (UDO-) - Body ground Always 10 kΩ or higher
I146-3 (UDO+) - Body ground Always 10 kΩ or higher
I146-4 (UJSG) - Body ground Always 10 kΩ or higher
I146-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Reconnect the radio receiver assembly connector.


b.
E210105C10
0.51,2 1.042,2.292 0.531,0.292 1.479,2.063 1.01,1.76 false 1.979,2.083 2.375,2.083 false 0.604,2.063 0.958,2.219 0.354,0.156 10 I146 0.74,1.656 1,1.813 0.26,0.156 10 UPI 0.115,0.01 0.375,0.167 0.26,0.156 10 *a 2.406,2.01 2.802,2.167 0.396,0.156 10 UJSG
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I146-4 (UJSG) Ignition switch ACC 5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device.

Ensure that backup music data is available before performing this operation.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.


HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION



Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the radio receiver assembly, and if information such as track, artist and album names are displayed on the screen.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG